User manual PENTAX OPTIO 50

[. . . ] FCC STATEMENT (For customers in USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Press the MENU button, then use to select the [Mode2] menu. Use to select [Drive Mode], then press the button. Mode1 Focus Drive Mode AE Metering Mode2 Mode3 Std. OK: Exit : 2/3 4. Use or to select [HS Continuous], then press the 5. To exit the menu, press the MENU button. The indicator is displayed on the monitor screen. Press the shutter button halfway to lock the focus. Press the shutter button to capture the image. button. Std. Drive Mode HS Continuous Auto Bracket OK : Exit : 2/3 In High Speed Continuous mode, the flash mode will be set to OFF automatically. EN-34 Auto Bracket In this mode, the camera automatically changes the exposure within a set range to take three shots after you press the shutter button once. Auto Bracket settings can be combined with exposure compensation settings to extend the adjustment range. Rotate the mode dial to , , , , or and turn your button. Press the MENU button, then use to select the [Mode2] menu. Use to select [Drive Mode], then press the button. Use or to select [Auto Bracket], then press the button. To exit the menu, press the MENU button. The indicator is displayed on the monitor screen. Press the shutter button to capture the image. Drive Mode Std. HS Continuous Auto Bracket OK : Exit : 3/3 In Auto Bracket mode, the flash mode will be set to OFF automatically. EN-35 Selecting the Metering Mode You can select the metering mode that sets which part of the subject to measure to determine the exposure. Rotate the mode dial to camera on by pressing the button. Press the MENU button, then use to select the [Mode2] menu. Use to select [AE Metering], then press the Mode1 Focus Drive Mode AE Metering Mode2 Mode3 Std. OK : Exit : 3/3 4. Use or to select the desired metering mode, then press the button. [ Center-weight]: Averages the light metered from the entire frame, but gives greater weight to the subject matter at the center. [ Spot]: The exposure is determined by the small area in the center of the screen only. [. . . ] Quality 2560 x 1920 5M 2048 x1536 3M 1280 x 960 1. 2 M 640 x 480 0. 3 M Resolution (Compression Ratio) Best (1/4) Better (1/8) Good (1/16) Best (1/4) Better(1/8) Good (1/16) Best (1/4) Better (1/8) Good (1/16) Best (1/4) Better (1/8) Good (1/16) Internal Memory (12MB) 4 8 17 6 13 27 17 33 64 64 128 257 SD Memory Card 32MB 11 22 44 17 33 67 42 82 157 157 315 631 64MB 22 45 90 34 69 138 86 168 322 322 645 1291 128MB 45 91 182 70 139 279 174 340 652 652 1305 2610 256MB 91 181 362 140 278 557 346 678 1300 1300 2600 5201 512MB 183 365 731 283 561 1122 698 1388 2620 2620 5240 10480 The above data shows the standard testing results. The actual capacity varies according to the shooting conditions and settings. EN-73 Approximate Duration of Recording Time The table below indicates the approximate duration of recording time depending on the capacity of the internal memory and the SD memory card. Image size 320 x 240 Internal Memory (12MB) 00:56 32MB 02:19 64MB 04:47 SD Memory Card 128MB 09:42 256MB 19:20 512MB 39:00 The values for the recording time may vary depending on the shooting conditions and settings. EN-74 WARRANTY POLICY All PENTAX cameras purchased through authorized bona fide photographic distribution channels are guaranteed against defects of material or workmanship for a period of twelve months from date of purchase. Service will be rendered, and defective parts will be replaced without cost to you within that period, provided the equipment does not show evidence of impact, sand or liquid damage, mishandling, tampering, battery or chemical corrosion, operation contrary to operating instructions, or modification by an unauthorized repair shop. [. . . ]