User manual PENTAX SPORT 35 MOTOR

[. . . ] Case Operating manual (this manual) Certification PENTAX is a trademark of HOYA CORPORATION. FOR THE SAFE USE OF YOUR FLASH UNIT Although we have carefully produced this flash unit for safe operation, please be sure to especially follow warnings and cautions given on page 2. WARNING This symbol indicates that violating this item could cause serious personal injuries. CAUTION This symbol indicates that violating this item could cause minor or medium personal injuries, or material losses. is a symbol indicating items that are prohibited. is a symbol emphasizing a warning. 1 WARNING The flash contains electronic circuits that operate at high voltages. Do not attempt to disassemble the flash unit yourself, as there is danger of an electric shock. [. . . ] By changing the camera's function settings, you can set the built-in flash unit so that it is not the main flash. Refer to the operating manual for the camera to find out how. For test flash, refer to page 55. 38 When Attaching the AF360FGZ to the Camera for Control Flash Main flash Control flash only: not used for main flash (Preparation of Flash Unit Attached to Camera) 1 Firstly, set the wireless mode and channel of the AF360FGZ attached to the camera, and register the channel on the camera. Attach the AF360FGZ to the hot shoe of the camera after turning the camera off. Set the power switch of the flash unit to (WIRELESS). Set the wireless mode switch to (C), so that CONTROL is displayed in the upper right corner of the LCD panel. Slide down the setting switch to the (yellow dot) to display the channel on the LCD panel. Press the channel button (CH) and select a channel from 1CH to 4CH. Slide the setting switch back up to the (white dot). 39 When you turn the camera on and press the shutter release button halfway down, the channel of the flash unit is registered on the camera. (Preparation of Separated Flash Unit) Next, set the channel of the separated (wireless) flash unit to the same channel as the flash unit attached to the camera. Place the other AF360FGZ in the desired position. Set the power switch of the flash unit to (WIRELESS). Set the wireless mode switch to (S), so that SLAVE is displayed in the upper right corner of the LCD panel. Press the channel button (CH) and select a channel from 1CH to 4CH. Slide the setting switch back up to the (white dot). 43 Next, remove the flash unit from the camera and place it in the desired position. Press the flash mode button (MODE) to display (P-TTL) if the flash mode was set to the modes other than P-TTL. 2 3 4 5 6 When you turn the camera on and press the shutter release button halfway down, the channel is registered on the camera. If the shutter speed is the same or slower than the X-sync speed of the camera, the flash will be set to P-TTL mode, and when it is faster than Xsync speed, the flash will be set to high-speed sync mode. Confirm that the AF360FGZ and built-in flash unit are fully charged, and take the photograph. A lamp on the wireless flash unit will blink. The built-in flash unit is used for control flash only. Refer to camera's operating manual for the operation of the camera. 7 Set the zoom position. (Refer to page 18) Set the zoom position with (M. Zoom) regardless of the lens you use. Enable the built-in flash unit of the camera and display ( ) on the LCD panel. Set the sync mode switch of the wireless flash unit to leading curtain sync ( ). Set the exposure mode of the camera to manual exposure and the shutter speed faster than Xsync speed. 44 (Using the AF360FGZ in Combination with another AF360FGZ) Set the wireless mode switch to (C) or (M). [. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]