User manual PENTAX ZOOM 70

[. . . ] Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks · The SD logo is a trademark. · PENTAX is a trademark of PENTAX Corporation. · Optio is a trademark of PENTAX Corporation. [. . . ] Use the four-way controller (23) to select the required mode. Press the shutter release button. The picture will be taken. 200 10/20/2003 11:19 Playing Back Still Pictures 1 p. 26 · The picture mode will be saved when the camera is turned off. · The flash is disabled in Fireworks mode and the focus is fixed at infinity. · The four-way controller (23) becomes the manual focus button and cannot be used to change the picture mode when the focus mode is set to manual. Press the OK button once and then use the four-way controller (23) to change the picture mode to change the picture mode. · To avoid camera movement in Night-scene, Sunset and Fireworks mode. You are recommended to fix the camera on a tripod. 4 Taking Pictures 61 1 3, 4 2 5 4 Taking Pictures 62 Taking Panorama Pictures (Panorama Assist Mode) Using the provided software (ACDSeeTM), join several pictures on your PC and easily create panoramic photos. Join photos that have been taken so the edges of the images overlap in Panorama Assist Mode to create a single panoramic photo. 1 2 Set the mode dial to F. Use the four-way controller to choose the direction in which the images will be joined. 4 5 2 3 S e t s h i f t directionn Set shift d i r e c t i o Joins the images at the left. The example shows the images when 5 is selected. 3 Take the first picture. Press the shutter release button to take the first image. The right edge of the image is displayed in transparent form on the left of the LCD monitor. 10/20/2003 11:19 4 Move the camera to the right and take the second picture. Position the camera so that the actual image display overlaps the transparent display on the left edge, and then release the shutter. For example, if the subject is 3m away, the distance the camera should be moved will be 3m ÷ 40=7. 5cm. However, as the way people see three-dimensional images differs from person to person, there is no need to be too concerned. Refer to the table below for a simple guide to how far to move the camera. Distance to subject Camera movement 0. 1 m 0. 5 cm 0. 3 m 1 cm 0. 5 m 1. 5 cm 1m 2. 5 cm 3m 7. 5 cm 5m 13 cm 65 Viewing 3D pictures by the parallel method and cross method As our eyes are positioned about 6 ­ 7 cm apart, there is a very slight deviation between what we see with our right eye and what we see with our left eye. The difference is processed by our brain to produce a three-dimensional image. This principle is applied to taking and viewing 3D pictures. 3D pictures can be viewed by the parallel method where the left and right lines of vision are virtually parallel, as when looking at a distant scene, or the cross method where the left and right lines of vision are crossed, as when you cross your eyes. A certain amount of practice may be necessary to view 3D pictures without using the viewer. How to Assemble the 3D Image Viewer Assemble the 3D image viewer supplied with the camera as shown below. 4 Taking Pictures 66 How to view 3D pictures using the 3D image viewer Print out the pictures so that they are about 11cm or 12cm wide and place the divider of the 3D image viewer in the middle of the two. 4 Taking Pictures As the distance between the left and right eyes differs from person to person, some people may have difficulty obtaining a three-dimensional effect even when looking at prints that are the same size. It may be especially difficult if the pictures are very large or very small. Try different sizes until the right effect is achieved. · Never look at the sun through the 3D image viewer. [. . . ] Therefore, we recommend that you review the warranty card supplied with your product at the time of purchase, or contact the PENTAX distributor in your country for more information and to receive a copy of the warranty policy. 139 7 Appendix 7 Appendix 140 For customers in USA STATEMENT OF FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]