User manual PET SAFE ELECTRONIC PET FEEDER

[. . . ] com/Ce/ DJ-S17E: VHF FM Transceiver 144. 000~145. 995MHz DJ-S47E: UHF FM Transceiver 430. 000~439. 995MHz This device is authorized for use in all EU and EFTA member states. An operator's license is required for this device. No part of this document may be reproduced, copied, translated or transcribed in any form or by any means without the prior written permission of Alinco. Inc. , Osaka, Japan, English Edition Printed in Japan. 3 Warning Warning To prevent any hazard during operation of Alinco's radio product, in this manual and on the product you may find symbols shown below. [. . . ] The (minus) and icons appear on the display. By default, the values are: DJ-S17E/TFH: minus shift, 0. 6MHz offset, 88. 5Hz CTCSS tone DJ-S47E: minus shift, 7. 6MHz offset, 88. 5Hz tone If these are the values you desire, no further setting is required so simply press the key to go back to the operation mode. Refer to "Repeater-Access" on page 41 for operation. To change the values instead, repeat the same setting sequence explained on page 26 for shift direction and offset frequency then page 37 for CTCSS tone by entering to the Set mode while is displayed. Even if you desire the same values you set for the respective parameters in the VFO mode, please repeat the sequence in here to activate the Repeater-Access function. After having completed the programming in the Set mode, return to the menu by pressing any key except FUNC or MONI. Press the FUNC key and while is displayed, press the key. A beep sounds and the new values are stored in the memory. NOTE: You can not communicate in the channel. You can not delete or convert this memory to other purposes. 4 4. 5. 6 Programmable Parameters in Memory Channels The following parameters can be stored in each of the memory channels. · Frequency · Offset frequency * · Skip channel setting · Shift direction (+/-) * · Busy channel lockout (BCLO) · Tone encoder frequency * · Transmission power (H/L) · Tone decoder frequency * · Battery save setting · Tone encoder/decoder setting (TSQ) * · Clock Shift setting · DCS code * · Alphanumeric channel tag · DCS setting * · Attenuator Level NOTE: Only parameters marked "*" are programmable in Repeater-Access function memory. 29 4. Basic Operation 4. 6 Call-Channel Mode This mode is used to recall a most frequently used memory channel (stored in MC channel) with a single key-touch. You can not transmit in this state. 4 4. 8. 1 Selecting the Output Level Press the FUNC key, and while is displayed on the LCD, press the key to switch between high and low transmission power output. When the low power output is selected, " " is displayed on the LCD (nothing is displayed when the high power is selected). The Power-meter display is when transmitting at the low power, and when transmitting at the high power. IMPORTANT NOTE: The output level can't be altered while transmitting. 31 5. Useful Functions 5. Useful Functions 5. 1 Scan Modes The scan function automatically searches the receiving signals. There are 2 modes for scan-resume condition. · Timer Scan : The scan stops when a signal is detected, and resumes scanning after 5 (default) seconds regardless of receiving status. · Busy Scan: The scan stops when a signal is detected, stays until the signal is gone then resumes scanning. During scanning, the 1MHz decimal point ( ) on the frequency display flashes. Press any key other than the MONI key to stop scanning. Scanning starts in the direction of the last dial operation (up or down). 5 NOTE: Please refer to the Set mode to switch the setting between Timer and Busy scan modes (page 43). 5. 1. 1 VFO-Scan 1. [. . . ] Make sure that the characters A, B and C on both sides of the stand match each other and the plate is placed all the way down to the bottom. Installation Positions of the Adjustment Plate When mounting only the battery (EBP-63/65) When mounting only the battery (EBP-64) A B C A B C A B C A B C EBP-63/65 When mounting the battery attached to the unit (EBP-63/65) When mounting only the battery (EBP-66) When mounting the battery attached to the unit (EBP-66) When mounting the battery attached to the unit (EBP-64) EBP-64 4. Mount the battery (with or without being attached to the unit) in the basket as shown. The red indicator on the basket turns on and charging starts. 10 NOTE: You can charge the battery pack using a basket (EDC-143/144) even if the battery charge function is set to "CHG-OF". 58 EBP-66 10. Maintenance and Reference 5. The red indicator turns off when the charge is completed. [. . . ]