User manual PFAFF 1029 ELECTRONIK

[. . . ] -- . — I c-I) L C) I ‘. D / i Fold out this page Some safety rules Contents Removing the carrying case cover Openng the hinged top cover Removing and opening the swIng-out arm Accessory box and accessory compartment Electrical connection and foot control Placing spool of thread on pin Upper threading Threading he needle Disengaging the sewing mechanism Winding the bobbin Removing bobbin case and bobbin iflsertng the bobbin Inserting the bobbin case Drawing up the bobbin thread Presser bar lifter Thread cutter Thread tension Regulating the stitch length Reverse sewing Finger-tip controls Selecting utility stitches Selecting stretch stitches Utility- and stretch-stitch combinations Selecting the needle position for straight stitching Dropping the machine feed Changing the needle Biectronic bobbin thread monitor Needle positioner Basting Electronic top speed selector Changing the sewing feet Sewing feet Speciai sov;ng toot Sewing buttonholes Changing the light bulb Cleaning and oiling Changing the fuse Troebie shooting Page 1 a) Be careful to avoid injuring your fingers on the needle when sewing. b) Make sure you unplug the power cord whenever you have to change the needle, sewing foot, bobbin or needle plate, or when you clean or oil the machine or have to interrupt sewing and leave the machine for a while. c) Only use a 15-watt light bulb in the sewing lamp. 2 3 4 4 5 5 6 7 7 8 8 9 9 10 ii 11 12 13 13 14 14 15 15 16, 17 16, 17 16. 17 16, 17 18 19 20 20. 21 22 22 23 24, 25 Parts of your sewing machine 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 Carrying handle Hinged top cover Hand wheel Stop motion knob Master switch Finger-tip controls Stitch length control Swing-out sewing arm with accessory compartment Needle plate Sewing foot holder with sewing foot Needle holder with screw Needle thread tension Presser bar lifter Presser bar with thread cutter Reverse-teed control Stitch chart Space for entering phone numbei of customer service Accessory box with accessory compartment underneath Bobbin winder Top speed regulator Basting stitch button Foot control Free arm cover, enclosing sewing hook Free arm Thread guide Threading SlOtS Take- up lever Spool pin with unreeling discs Threading slot for bobbin winding Bobbin tension stud (bobbin winding) Bobbin rack Bobbin thread monitor Needle positioner (“up and down posihoning) j I I 4 N ) SiJOSSODD POWWODDE pu () O () p S uedQ (c) no H 9I L4 pJEMo nO H UiMS () puq JflOA HHM WJU nO-buiMS eL JepUn qDEe uije no-6u!MS eqj 5uiudo pu 6uowaH p JeAOD 8L4 iJ ULJ (v) Si J8L AOD 81 epiSUi P14D 1DiS u Aq paipui ss ai eq o ejpu L4 pjot ‘eAOD eSD bUi/HJE3 eq o 0j PUH IRM °A [ JAOD 3q fl pe6uq 6uiuad JAO3 dO AO eseD 6u ie eq 6U!Aowe 8 t p. — C CD U;CD 0 C — 3 ® 0 — a — CD’< oo a Co DO o-i CD DC) CDO OCt Cd) 0. [. . . ] Machine skips stitches Needle not rserted correctly. Push needle up as far as it will go, its flat shank side facing toward the back. Insert system 130/705 H needle. Insert new needle. Check threading. Select needle according to Needle and Thread Chart. 2. Needle thread breaks For any of the above reasons. Poor-quality or knotty thread used, or thread that has become too dry by excessive storage. Needle breaks Needle not pushed up as far as it will go. Needle bent and strikes needle plate because work is pushed or pulled. Insert new needle and push it up as far as it will go. See Needle and Thread Chart Let nachine feed the work alone. When inserting the bobbin case, press against it until it snaps into place. Regulate thred tensions Used only good-quality thread. 4. Seam is not uniform Tension Out of adjustment. During bobbin winding, do not hold tnread in hand, but pass it through the bobbin tension stud. Thread machine properly and check both tensions. Kinks appear on top and bottom of material. 24 4 Cause: 5. Machine feeds irregularly or not at all Lint has accumulated between tooth rows of feed dog. Machine runs with difficulty Thread ends in hook raceway. Remove thread ends and put a drop of oil into hook raceway. Electronic bobbin thread monitor does not function Remove thread ends and dirt. Special Thread ends and dirt have collected in care should be taken in the area round over the indicator the free arm cover the second indicator lamp. lamp, n the hook raceway, in the bobbin case, behind the hook and on the second indicator lamp to the right behind the hook. The machine only sews slowly, the needle has no piercing power and the electronic system is not functioning Move the winder to the left (switch off) The bobbin winder is engaged: it is at the right. 9. [. . . ] At the beginning of the seam lift up the teeth a little to feed them into the guiding groove. Sew the seam to the end and secure it. — \ 8oL Close zi Pin other side of zip to material at beginning of seam (Fig. Remove the pin, turn Out the right seam allowance wth the zip tape, and pin the atter to the fabric, as shown in Fig. The zip teeth now run into the right guiding groove in the foot (Fig. [. . . ]