User manual PHILIPS 104E

[. . . ] With microprocessor based digital controlled circuit, the monitor can automatically adjust itself to the video card's scanning frequency and displays an image with precise parameters you desire. The wide range of scanning frequency supports variety of operating platforms, such as IBM PC and compatibles, including Intel based platforms such as 386, 486, Pentium and Pentium II. E N Feature Highlights · · · · Global Styling demonstrates a soft & smart image. Digital Control feature provides user-friendliness and ease-of-use when operating the monitor. Anti-Glare screen coating eliminate any bad effects caused by the screen surface such as reflection of the room lights. [. . . ] Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount of materials to be disposed of. Please inform yourself on local regulations on disposal of your old set. 3 E N Installation Important: Please refer to the user's manuals of your computer and video adapter to make sure these equipments are properly installed and configured before installing the monitor. Positioning / Ventilation x Avoid exposing the monitor to direct sunlight, stoves or any other heat sources. x To prevent overheating, make sure that the ventilation openings of the monitor are not covered. x Keep away from any magnetic objects, such as speakers, electric motors, transformers, . . . etc. x When positioning this monitor, make sure that the mains plug and socket are easily accessible. Pedestal With the built-in pedestal you can tilt and / or swivel the monitor for a most comfortable viewing angle. To fit the pedestal, refer to the illustration on the inside front-cover of this manual. 104 E FUNC. RECALL 4 Connection Important: Please make sure the AC power to your computer is "OFF" before connecting or disconnecting any display peripheral. Failure to do so may cause serious personal injury as well as permanent damage to your computer equipments. E N Intel Based platform: 386, 486, Pentium, or other compatibles: · Connect the monitor to the computer using the supplied interface cables. Monitor rear view 1) IBM PC connection 2) Mains connection WARNING:SHOCK HAZARD-DO NOT OPEN AVIS:RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO, NO ABRIR 2 1 5 E N Connection to the mains (Rear of the monitor) WARNING:SHOCK HAZARD-DO NOT OPEN AVIS:RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO, NO ABRIR (Mains cord) Connecting to the mains This monitor is set to operate at a mains supply of 100-240 volts AC. If the mains voltage in your home is not between this, consult your dealer. Connect one end of the mains cord to the mains socket at the rear of monitor, and the other end to the mains supply. The monitor will be operating in power saving mode if you switch on your monitor without signal input from PC. (Please refer to Power Management Signalling instruction. ) 6 Front Control locations and functions 104 E E N FUNC. RECALL FUNC. RECALL For an optimized adjustment of the picture following controls are available at the front. Press this knob, the green LED lights and the power is ON. Press this knob again, the green LED disappears and the power is OFF. When pressing the "FUNC" key, the LED will flash to indicate the function has been selected. When function has been selected, press picture image. CONTRAST Used to adjust the picture contrast level. BRIGHTNESS Used to adjust the overall screen brightness as a compensation for ambient light. or to adjust 7 E N H-Size : to adjust the horizontal amplitude of the image. H-Center : to adjust the horizontal position of the image. V-Size : to adjust the vertical amplitude of the image. [. . . ] 1 2 3 4 5 6 7 8 Assignment Red video input Green video input Blue video input Identification output - Connected to pin 10 Ground Red video ground Green video ground Blue video ground Pin No. 9 10 11 12 13 14 15 Assignment No pin Logic ground Identification output - connected to pin 10 Serial data line (SDA) H. Sync (VCLK for DDC) Data clock line (SCL) Because of a policy of continuous product improvement, the above specifications are subject to change without notice. 12 14E4220T Digital Auto Scan Colour Monitor Contents English Introduction Feature Highlights Safety precautions and maintenance Package End of life disposal Installation Connection Connection to the mains Front Control locations and functions Adjustment Technical information . . . . 11 E N 13 E N OTHER LANGUAGE VERSIONS FRENCH(FRANÇAIS) . . . . [. . . ]