User manual PHILIPS 14PV170

[. . . ] & OPERATING INSTRUCTIONS IN BRIEF The remote control RECORD n Record STANDBY m Standby switch TIMER k TIMER programming on the set CLEAR b 0-9 H I Reset/clear Digit buttons 0-9 Rewind/Reverse scanning Forward wind/ Forward scanning STOP Front of the set mSTANDBY Standby switch VOLUME p Volume control PROGRAMME p Programme number Plus/Minus nRECORD HSPEED Record Rewind/Reverse scanning Pause/Stop STOP h Pause/Stop GPLAY Playback PLAY Playback SPEED I Forward wind/ Forward scanning D Menu left C Menu right Sp Volume control A B Pp MUTE y MENU OK INDEX E STILL R menu Up menu Down Programme number Plus/Minus Mute sound Call menu Confirm button Index search Still picture EJECT J Cassette eject PHONES Headphones socket & How to enter, check or clear a TIMER-block manually 1 2 3 4 Press the TIMER k button. CLEAR b D Select a free TIMER block or the TIMER block you want to check or clear. Enter/Check: Press the or C button to switch between 'DATE' (date), 'DW' (daily, weekly), 'PR' (programme number), 'START' (start time) and 'END' (end time). A and the B or the 0-9 buttons to change the data. Press the To end programming, press the Press the STANDBY m MENU 5 6 button. button. Selecting a TV channel Select the required TV channel (= programme number) with the P p button or the 0-9 buttons on the remote control. [. . . ] 3 Picture search: Now press the H (rewind) or (wind) button once or several times. 4 Interrupt: Press the STOP h Tape position: If you press the OK button the tape position will be shown in the display during Wind, Rewind, Record, Play back and Pause/Stop. Index search: Every time you start to record, the tape is marked with a code mark. 1 Press the button. H 5 Wind: Stop the tape and press the I (rewind) or the (wind) button. EJECT J 6 Eject: Press the button on the set. button. Press the I button to select the next code mark or the H button for the previous code mark. INDEX E Note: Some functions switch off automatically after a while (e. g. : Pause, Still Picture, Scanning). This helps to protect the cassette and prevent unnecessary power consumption. * With this set you can play back cassettes that have been recorded on another TV combi in the NTSC standard. * If you load a cassette with erase protection, the TV combi starts the play back automatically. * The picture quality is affected during scanning. * Remove the cassette before transporting the TV Combi. 2 Once the TV Combi finds the code mark or unrecorded area it will automatically switch to play back. Note: When you press any tape transport button (e. g. : the H or I button) this search function will be stopped. * You cannot use this function with recordings made on another video recorder that does not have this function. Eliminating picture interference 1 During playback press the MENU button. Still picture 1 Press the 2 Select and confirm the 'SPECIAL' line. With the D or the C button you can change the end time of the recording in 30 minute intervals. If you wish to cancel the end time, press the CLEAR b button. The recording goes on uninterruptedly. (This does not effect the recording. ) Programme number 'E1' is provided for recording from external sources (via the EXTERNAL scart socket). Erase protection: So that you don't accidentally delete an important recording, you can remove the special tab (erase protection) on the narrow side of the cassette with a screwdriver or slide the special tab to the left. Later, if you no longer want the cassette to be erase protected, you can seal the gap again with adhesive tape or slide the special tab to the right. Auto-assembling: You can use the auto-assembling function to join individual recordings without any major picture disturbance between the recordings. Search for the correct position on the tape and then stop the playback by pressing the STOP h button. 'PAUSE' appears in the display. Now start recording as usual by pressing the RECORD n button. Long play: Before recording, press the MENU button. Select and confirm the 'SPECIAL' line. Select and confirm the 'TAPE SPEED' line. [. . . ] DECODER STORE vw C-21 1 Note: If a button is pressed with the childlock 'on', 'CHILD LOCK' appears for a few seconds in the display. * Programmed recordings are made despite the child lock and cannot be interrupted. 3 Select the 'SEARCH' line. 4 Press the button as often as necessary, until you have found the right TV channel. C Note: * If you want to allocate a decoder, switch the decoder function on or off with the D or C button in the 'DECODER' line. * If you want to change the automatic channel setting, select the 'FINE TUNING' line. [. . . ]