User manual PHILIPS 14PV182

[. . . ] & OPERATING INSTRUCTIONS IN BRIEF The remote control RECORD n Record STANDBY m Standby SV/V+ 'VIDEOPlus+' programming Front of the set m Standby Pp Programme number Plus/Minus Sp Volume control 5 H TIMER k TIMER programming on the set CLEAR b 0-9 Reset/clear Digit buttons 0-9 Record Rewind/Reverse scanning STOP h Pause/Stop GPLAY Playback h Pause/Stop G I J w Playback Forward wind/ Forward scanning Cassette eject Headphones socket D Menu left C Menu right Sp Volume control A B Pp MUTE y MENU OK INDEX E STILL R menu Up menu Down Programme number Plus/Minus Mute sound Call menu Confirm button Index search Still picture The following buttons are only available for some sets: CLEAR b d e f g TELETEXT concealed information TELETEXT off (temporarily) TELETEXT on/off TELETEXT page stop TELETEXT enlarged print & Programming with 'VIDEOPlus+' All the information required for programming is encoded in the 'VIDEOPlus+' code. 1 2 How to enter, check or clear a TIMER-block manually 1 2 3 4 Press the TIMER k button. CLEAR b D Press the SV/V+ button on the remote control. Select a free TIMER block or the TIMER block you want to check or clear. Enter/Check: Press the or C button to switch between 'DATE' (date), 'DW' (daily, weekly), 'PR' (programme number), 'START' (start time) and 'END' (end time). A and the B or the 0-9 buttons to change the data. Press the To end programming, press the Press the STANDBY m MENU Enter the entire 'VIDEOPlus+ code'. [. . . ] You can store up to 69 TV channels. channel to which you want to allocate a programme number, e. g. : 'P 01' . 4 In the line 'TO' , select the required programme number, e. g. : 'P 02' . 5 Select and confirm the line 'STORE' . The allocated TV channels will be exchanged. 6 Repeat steps 3to 5until you have allocated a pro- gramme number to all the required TV channels. To finish, press the MENU button twice. 4 2. PLAY BACK Tape position/Index search I 1 Insert a cassette into the cassette slot. A blue screen appears for a few 3 Select the 'REPEAT PLAY' line. Switch on the continuous seconds. 0 Wait until the blue screen disappears and press the playback. 4 Press the MENU button. MENU button. 5 Start the continuous playback with the GPLAY playback button. 6 If you want to cancel the function, stop the continous Note: * Some hired cassettes may have a poor picture/sound quality. This is not a fault in your set. playback in the 'REPEAT PLAY' line. 5 3. RECORD Programme a recording The set needs the following information for every programmed recording: * the date on which the recording is to be made * the programme number for the TV channel * the start and end time of the recording * VPS/PDC on or off The set stores all the information mentioned above in what is known as a TIMER block. It can store 6 TIMER blocks for up to one month in advance. 1 Insert a cassette. 2 Use the P p button to select the programme number from which you wish to record, e. g. : 'P 01' . 3 Press the RECORD n button. 4 Use the STOP h button to stop the recording. 5 If, whilst recording, you want to switch off the TV screen, press the STANDBY m button once. To switch the TV screen on again, press the button. Pp Important notes for recoding · OTR: If you do not want to record to the end of the cassette, press the RECORD n button again. The display shows at what time the recording will stop. With the D or the C button you can change the end time of the recording in 30 minute intervals. If you wish to cancel the end time, press the CLEAR b button. The recording goes on uninterruptedly. (This does not effect the recording. ) Programme number 'E1' is provided for recording from external sources (via the EXTERNAL scart socket). Programme number 'AV' is provided for recording from external sources (via the front socket). Erase protection: So that you don't accidentally delete an important recording, you can remove the special tab (erase protection) on the narrow side of the cassette with a screwdriver or slide the special tab to the left. Later, if you no longer want the cassette to be erase protected, you can seal the gap again with adhesive tape or slide the special tab to the right. Auto-assembling: You can use the auto-assembling function to join individual recordings without any major picture disturbance between the recordings. Search for the correct position on the tape and then stop the playback by pressing the STOP h button. 'PAUSE' appears in the display. Now start recording as usual by pressing the RECORD n button. Long play: Before recording, press the MENU button. Select and confirm the 'SPECIAL' line. [. . . ] button to select the required programme number, e. g. : 'P 01' . Note: If a button is pressed with the childlock 'on', 'CHILD LOCK' appears for a few seconds in the display. * Programmed recordings are made despite the child lock and cannot be interrupted. 6 Select and confirm the 'STORE' line. 7 If you want to search for further TV channels, start again Manual channel search In certain cases the Automatic Channel Search may not be able to find all of the TV channels (e. g. : coded TV channels). You can then use this manual method to set the channels. 1 Switch on the set with the D STOP h button. [. . . ]