User manual PHILIPS 14PV274

[. . . ] & OPERATING INSTRUCTIONS IN BRIEF The remote control RECORD n Record STANDBY m Standby switch SV/V+ 'VIDEOPlus+' programming Front of the set m Standby switch Pp Programme number Plus/Minus Sp Volume control n Record H TIMER k TIMER programming on the set CLEAR b 0-9 H I Reset/clear Digit buttons 0-9 Rewind/Reverse scanning Forward wind/ Forward scanning Rewind/Reverse scanning h Pause/Stop G I J w Playback Forward wind/ Forward scanning Cassette eject Headphones socket STOP h Pause/Stop GPLAY Playback D Menu left C Menu right Sp Volume control A B Pp MUTE y MENU OK INDEX E STILL R menu Up menu Down Programme number Plus/Minus Mute sound Call menu Confirm button Index search Still picture The following buttons are only available for some sets: CLEAR b d e f g TELETEXT concealed information TELETEXT off (temporarily) TELETEXT on/off TELETEXT page stop TELETEXT enlarged print & Programming with 'VIDEOPlus+' All the information required for programming is contained encoded in the 'VIDEOPlus+' code. 1 2 How to enter, check or clear a TIMER-block manually 1 2 3 4 Press the TIMER k button. CLEAR b D Press the SV/V+ button on the remote control. Select a free TIMER block or the TIMER block you want to check or clear. Enter/Check: Press the or C menu button to switch between 'DATE' (date), 'DW' (daily, weekly), 'PR' (programme number), 'START' (start time) and 'END' (end time). A and the B or the 0-9 buttons to change the data. Press the To end programming, press the Press the STANDBY m MENU Enter the entire 'VIDEOPlus+ code'. [. . . ] MENU 6 Cleaning function: Press the button. button. 7 Select and confirm the 'SPECIAL' line. 9 Press the OK 2 Select and confirm the 'SPECIAL' line. 3 Select the 'REPEAT PLAY' line. Start the continuous playback. 4 Press the MENU button. A blue screen appears for a few button. seconds. 0 Wait until the blue screen disappears and press the MENU 5 Start the continuous playback with the GPLAY playback button. 6 If you want to cancel the function, stop the continous button. playback in the 'REPEAT PLAY' line. Note: Some hired cassettes may have a poor picture/sound quality. This is not a fault in your set. 5 3. RECORD Programme a recording The set needs the following information for every programmed recording: * the date on which the recording is to be made * the programme number for the TV channel * the start and end time of the recording * VPS/PDC on or off The set stores all the information mentioned above in what is known as a TIMER block. It can store 6 TIMER blocks for up to one month in advance. 1 Insert a cassette. 2 Use the P p button to select the programme number from which you wish to record, e. g. : 'P 01' . 3 Press the RECORD n button. 4 Use the STOP h button to stop the recording. 5 If, whilst recording, you want to switch off the TV screen, press the STANDBY m button once. To switch the TV screen on again, press the button. Pp Important notes for recoding · OTR: If you do not want to record to the end of the cassette, press the RECORD n button again. The display shows at what time the recording will stop. With the D or the C button you can change the end time of the recording in 30 minute intervals. If you wish to cancel the end time, press the CLEAR b button. The recording goes on uninterruptedly. (This does not effect the recording. ) Programme number 'E1' is provided for recording from external sources (via the EXTERNAL scart socket). Erase protection: So that you don't accidentally delete an important recording, you can remove the special tab (erase protection) on the narrow side of the cassette with a screwdriver or slide the special tab to the left. Later, if you no longer want the cassette to be erase protected, you can seal the gap again with adhesive tape or slide the special tab to the right. Auto-assembling: You can use the auto-assembling function to join individual recordings without any major picture disturbance between the recordings. Search for the correct position on the tape and then stop the playback by pressing the STOP h button. 'PAUSE' appears in the display. Now start recording as usual by pressing the RECORD n button. Long play: Before recording, press the MENU button. Select and confirm the 'SPECIAL' line. [. . . ] * If you want to change the automatic channel setting, select the 'FINE TUNING' line. With the D or C button you can vary the automatic TV channel setting. Important: This re-tuning is only necessary and useful in special cases, e. g. when there are stripes on the picture with cable-TV systems. 5 In the 'PROGRAMME NR. ' line use the D or button to select the required programme number, e. g. : 'P 01' . [. . . ]