User manual PHILIPS 14PV284-05S

[. . . ] & OPERATING INSTRUCTIONS IN BRIEF The remote control STANDBY m Standby CLEAR 0-9 SV/V+ Reset/clear Digit buttons 0-9 'VIDEOPlus+' programming Front of the set m Standby Pp Programme number Plus/Minus Sp Volume control 5 H TIMER k TIMER programming on the set MENU OK Call menu Confirm button Record Rewind/Reverse scanning h Pause/Stop G I J w AUDIO VIDEO D/C/A/B Menu left/right/up/down Sp Volume control Pp MUTE y GPLAY H Programme number Plus/Minus Mute sound Playback Rewind/Reverse scanning Playback Forward wind/ Forward scanning Cassette eject Headphones socket Audio input socket Video input socket STOP h Pause/Stop I INDEX E RECORD n STILL R Forward wind/ Forward scanning Index search Record Still picture INFO , TELETEXT page 100 TRANSP. - TELETEXT transparent TELETEXT e CLOCK . TELETEXT on/off TELETEXT clock time In TELETEXT you can store the relevant page with the OK button. Selecting TELETEXT functions: when you are in TELETEXT, press the MENU button. [. . . ] 9 Press the 2 Select and confirm the 'SPECIAL' line. OK button. A blue screen appears for a few 3 Select the 'REPEAT PLAY' line. Switch on the continuous seconds. 0 Wait until the blue screen disappears and press the playback. 4 Press the MENU button. MENU button. 5 Start the continuous playback with the GPLAY playback button. 6 If you want to cancel the function, stop the continous Note: * Some hired cassettes may have a poor picture/sound quality. This is not a fault in your set. playback in the 'REPEAT PLAY' line. 5 3. RECORD Programme a recording The set needs the following information for every programmed recording: * the date on which the recording is to be made * the programme number for the TV channel * the start and end time of the recording * VPS/PDC on or off The set stores all the information mentioned above in what is known as a TIMER block. It can store 6 TIMER blocks for up to one month in advance. 1 Insert a cassette. 2 Use the P p button to select the programme number from which you wish to record, e. g. : 'P 01' . 3 Press the RECORD n button. 4 Use the STOP h button to stop the recording. 5 If, whilst recording, you want to switch off the TV screen, press the STANDBY m button once. To switch the TV screen on again, press the button. Pp Important notes for recoding · OTR: If you do not want to record to the end of the cassette, press the RECORD n button again. The display shows at what time the recording will stop. With the D or the C button you can change the end time of the recording in 30 minute intervals. If you wish to cancel the end time, press the CLEAR button. Programme number 'E1' is provided for recording from external sources (via the EXTERNAL scart socket). Programme number 'AV' is provided for recording from external sources (via the front socket). Erase protection: So that you don't accidentally delete an important recording, you can remove the special tab (erase protection) on the narrow side of the cassette with a screwdriver or slide the special tab to the left. Later, if you no longer want the cassette to be erase protected, you can seal the gap again with adhesive tape or slide the special tab to the right. Auto-assembling: You can use the auto-assembling function to join individual recordings without any major picture disturbance between the recordings. Search for the correct position on the tape and then stop the playback by pressing the STOP h button. 'PAUSE' appears in the display. Now start recording as usual by pressing the RECORD n button. Long play: Before recording, press the MENU button. Select and confirm the 'SPECIAL' line. Select and confirm the 'TAPE SPEED' line. [. . . ] With the D or C button you can vary the automatic TV channel setting. Important: This re-tuning is only necessary and useful in special cases, e. g. : when there are stripes on the picture with cable-TV systems. 5 In the 'PROGRAMME NR. ' line use the P p button to select the required programme number, e. g. : 'P 01' . 2 Select and confirm the 'FEATURES' line. 3 Select the 'CHILD LOCK' line. 5 Press the MENU 6 Select and confirm the 'STORE' line. [. . . ]