User manual PHILIPS 16905-87-16

[. . . ] Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. o Apparatus shall not be exposed to dripping or splashing. p Do not place any sources of danger on the apparatus (e. g. liquid filled objects, lighted candles). EN 5 English 2 Your Philips Wireless HD Net Connect Congratulations on your purchase and welcome to Philips! [. . . ] On mode with HDMI CH1 unrecognized video format On mode but HDMI CH1 without input from the computer/source device HDMI CH1 1080P On mode with recognized video format HDMI 1 2 Go to the source menu under the settings menu of your HDTV. Select the HDMI input to which the receiver is connected. 10 EN HDMI Activate the wireless link Switch on the transmitter and receiver Once the transmitter and receiver are powered up, the link is automatically established after 15-20 seconds. · · A flashing blue power LED is displayed until the signal link between the two units is established. Normally, it takes around 15-20 seconds for the link to establish successfully. When you unplug the power cord of the transmitter, the receiver enters standby mode after 5 minutes. » The power LED of the receiver lights up in red. The link between the transmitter and receiver is re-established when you plug in the power cord of the transmitter again. » The power LED of the receiver flashes in blue. Power LED Solid red Flashing blue Solid blue Solid blue Solid blue Status LED Off Flashing Flashing quickly Flashing slowly Solid blue Mode and status Standby mode for powersaving Setting up a Link between the transmitter and receiver On mode but without input from the computer/ source device On mode with unrecognized video format On mode with recognized video format · LED indicator status of the transmitter Power LED indicator Status Solid blue The link is established. Flashing blue Linking is in progress. Note · If the link is not established after 80 seconds, move the transmitter, receiver and HDTV closer to each other. The maximum transmission range is up to 23 feet (7 meters). If more than one set of Philips Wireless HD Net Connect is placed in the same room, make sure that the minimum distance among each one is 6 feet (2 meters). Make sure the computer is on and the video output on the laptop/PC is switched to HDMI. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note · The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all wireless product marketed in US must be fixed to US operation channels only. Notice for Canada This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Caution · The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e. i. r. p. Philips' liability is limited to repair or, at its sole option, replacement of the product. 16 EN The power LED on the receiver is not lit up in red in standby mode. The laptop screen image is not full screen on my TV. Make sure that there is power supply for the receiver. 1 2 3 4 5 6 Right-click on an open space on your desktop. Select Graphics Options > Output to > Digital Television (Now the laptop image will only appear on your TV). Once again, right-click on an open space on your desktop. On the pop-up box increase the resolution settings till the laptop image better fits your TV screen. Select OK and KEEP CHANGES when you are satisfied with your image size. [. . . ] » The screen with options is displayed. Select Clone, Extend display or Project out only for external display. Click on Start > Control Panel > Personalization > Display settings. Make sure that the display 2 is on with or without enabling Extend the desktop onto this monitor. [. . . ]