User manual PHILIPS 170CW8FB

[. . . ] Philips LCD Monitor Electronic User's Manual · Safety Precautions and Maintenance · FAQs · Troubleshooting · Regulatory Information · Other Related Information Safety and Troubleshooting Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your computer monitor: Operation: %Ï %Ï %Ï %Ï %Ï %Ï %Ï %Ï Keep the monitor out of direct sunlight and away from stoves or any other heat source. Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor's electronics. Do not block the ventilation holes on the cabinet. When positioning the monitor, make sure the power plug and outlet are easily accessible. [. . . ] If the monitor displays an image, installation is complete. RETURN TO TOP OF THE PAGE The Base · Front View Product Description · Accessory Pack · Connecting to your PC · Getting Started · Optimizing Performance · Remove the Base %Ï Remove the Base Condition: for VESA standard mounting applications Remove the 3 screws and then remove the base from the LCD monitor. Note: This monitor accepts a 100mmx100mm VESA-Compliant mounting interface. RETURN TO TOP OF THE PAGE Your LCD Monitor : · Front View Product Description · Setting Up and Connecting Your Monitor · Getting Started · Optimizing Performance Getting Started Getting Started Use the information file ( . inf) for Windows® 95/98/2000/Me/XP/Vista or later The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for Windows® 95/98/2000/Me/XP/Vista. This information file ( . inf) should be installed in order that your Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 95/98/2000/Me/ XP/Vista and the Plug & Play application can be activated. The installation procedure based on Windows® '95 OEM Release 2 , 98 , 2000 , Me, XP and Vista is specified as follows. For Windows® 95 1Start Windows® '95 . 2Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3Double click on the 'Display' Icon. 4Select the 'Settings' tab then click on 'Advanced. . . '. 5Select the 'Monitor' button, point to 'Change. . . ' then click on 'Have Disk. . . '. 6Click on the 'Browse. . . ' button, select the appropriate drive F: ( CD-ROM Drive) then click . on the 'OK' button. 7Click on the 'OK' button then select your monitor model and click on 'OK'. . For Windows® 98 1Start Windows® 98 . 2Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3Double click on the 'Display' Icon. 4Select the 'Settings' tab then click on 'Advanced. . . '. 5Select the 'Monitor' button, point to 'Change. . . ' then click on 'Next' . 6Select 'Display a list of all the drivers in a specific location, so you can choose the driver . you want. ' then click on 'Next' and then click on 'Have Disk. . . '. 7Click on the 'Browse. . . ' button, select the appropriate drive F: ( CD-ROM Drive) then click . on the 'OK' button. 8Click on the 'OK' button then select your monitor model and click on the 'Next' button. 9Click on the 'Finish' button then the 'Close' button. . For Windows® 2000 1Start Windows® 2000 . Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3Double click on the 'Display' Icon. 4Select the 'Settings' tab then click on 'Advanced. . . '. 5Select 'Monitor' . - If the 'Properties' button is inactive, it means your monitor is properly configured. - If the 'Properties' button is active. 6Click on 'Driver' and then click on 'Update Driver. . . ' then click on the 'Next' button. 7Select 'Display a list of the known drivers for this device so that I can choose a specific . [. . . ] At the lowest level, device may refer to a single hardware component, as in a memory device. At a higher level, it may refer to a collection of hardware components that perform a particular function, such as a Universal Serial Bus interface device. At an even higher level, device may refer to the function performed by an entity attached to the Universal Serial Bus; for example, a data/FAX modem device. Devices may be physical, electrical, addressable, and logical. Downstream The direction of data flow from the host or away from the host. [. . . ]