User manual PHILIPS 17A580BQ

[. . . ] Table of Contents 17A580BQ 19A580BQ GETTING STARTED Introduction . 11 SPECIAL CONTROLS WINDOW Video Input . 12 Advanced Controls / Up & Buttom Control . 13 Advanced Controls / Vertical Linearity . [. . . ] 8 K / 7 5HZ g e ome t r y EXIT RESET aud i o spe c i a l co l or 2a Turn the ROTARY knob, if necessary, turn the MUTE ON ma i n s c r een 1 6 0 0 x 1 2 00 9 3 . 8 K / 7 5HZ ROTARY knob until MUTE icon is highlighted. If you have sound, MUTE OFF appears at the top of the on screen display. g e ome t r y EXIT RESET co l or aud i o spe c i a l 1 6 0 0 x 1 2 00 9 3 . 8 K / 7 5HZ 5c When done, press the ON SCREEN DISPLAY button to save the change and return the screen to AUDIO CONTROLS. BALANCE 3a To select BASS, 50% 5b Turn the ROTARY knob to adjust the Balance. turn the ROTARY knob until BASS icon is highlighted. Next, press the ON SCREEN DISPLAY button. BASS 80% 5a To select BALANCE, turn the ROTARY knob until BALANCE icon is highlighted. Then, press the ON SCREEN DISPLAY button. TREBLE 3b Turn the ROTARY knob to adjust the Bass. 3c When done, press 4c When done, press the ON SCREEN DISPLAY button to save the change and return the screen to AUDIO CONTROLS. adjust the Treble. 4a To select TREBLE, 80% 4b Turn the ROTARY knob to turn the ROTARY knob until TREBLE icon is highlighted. Next, press the ON SCREEN DISPLAY button. the ON SCREEN DISPLAY button to save the change and return the screen to AUDIO CONTROLS. Smart Help To exit AUDIO CONTROLS . but continue on to SPECIAL CONTROLS, turn the ROTARY knob until required function is highlighted. Next, press the ON SCREEN DISPLAY button. to exit completely, press the ON SCREEN DISPLAY button and hold for 1. 5 seconds. To cancel MUTE, repeat step 2b, or press the MUTE button on the front of the monitor. To make changes to one item, follow the steps for that item. Then follow the instructions To exit AUDIO CONTROLS . . 11 How to Use the On Screen Display (OSD) Special Controls window Video Input VIDEO INPUT helps determine what you see on the screen. It is set at 0. 7V(olts), but if the video input signal is different than the output signal, you may want to change it to 1. 0V. OSD Controls WITH OSD CONTROLS, you can set the time for the On Screen Display to time out, and change the vertical and horizontal position of the OSD on the monitor screen. 1 B R IGHTNE SS ma i n s c r een g e ome t r y EXIT RESET aud i o spe c i a l co l or 1 6 0 0 x 1 2 00 9 3 . 8 K / 7 5HZ Press the ON SCREEN DISPLAY button. B R IGHTNE SS ma i n s c r een g e ome t r y EXIT RESET aud i o spe c i a l co l or 1 6 0 0 x 1 2 00 9 3 . 8 K / 7 5HZ 1 Press the ON SCREEN DISPLAY button. BR IGHTNESS ma i n s c r een 2 Turn the ROTARY BR IGHTNESS ma i n s c r een 2 Turn the ROTARY co l or g e ome t r y EXIT RESET co l or knob until the VIDEO INPUT icon is highlighted. g e ome t r y EXIT RESET aud i o spe c i a l aud i o spe c i a l knob until the OSD CONTROLS icon is highlighted. 1 6 0 0 x 1 2 00 9 3 . 8 K / 7 5HZ VIDEO INPUT ma i n s c r een ma i n OSD CONTROLS s c r een g e ome t r y EXIT RESET co l or 7 Turn the ROTARY g e ome t r y EXIT RESET co l or aud i o spe c i a l 1 6 0 0 x 1 2 00 9 3 . 8 K / 7 5HZ 5 Press the ON SCREEN DISPLAY button to save your selection and return to SPECIAL CONTROLS. knob to select either VERTICAL or HORIZONTAL POSITION and repeat steps 3 - 6. aud i o spe c i a l 1 6 0 0 x 1 2 00 9 3 . 8 K / 7 5HZ OSD CONTROLS TIMER 3 Press the ON SCREEN DISPLAY button. The VIDEO INPUT screen appears. 6 Press the ON SCREEN DISPLAY button to add your change and return to OSD CONTROLS. 3 Press the ON SCREEN DISPLAY button to bring up OSD CONTROLS screen. TIMER VIDEO INPUT 0. 7V 1. 0V 05 10 25 OFF 4 Turn the ROTARY knob to select either 0. 7V or 1. 0V. 5 Turn the ROTARY knob to select 05, 10, 25 seconds, or OFF. 4 Press the ON SCREEN DISPLAY button to bring up TIMER screen. Smart Help Smart Help After returning to SPECIAL CONTROLS . [. . . ] Make sure the monitor cable is properly connected to your computer. Check to see if the monitor cable has bent pins. Make sure the computer Power button is on. Make sure the D-Sub/BNC switch on the rear of the monitor is in the correct position. [. . . ]