User manual PHILIPS 17E422-2E-82

[. . . ] With microprocessor based digital controlled circuit, the monitor can automatically adjust itself to the video card's scanning frequency and displays an image with precise parameters you desire. The wide range of scanning frequency supports variety of operating platforms, such as IBM PC and compatibles. E N Feature Highlights · On-Screen-Display function provides more informations when the user operates the control functions. This feature provides userfriendliness and ease-of-use when operating the monitor. Anti-Glare and Anti-Static screen coating eliminate any bad effects caused by the screen surface such as reflection of the room lights and dust attraction. [. . . ] Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount of materials to be disposed of. Please inform yourself on local regulations on disposal of your old set. 3 E N Installation Important: Please refer to the user's manuals of your computer and video adapter to make sure these equipments are properly installed and configured before installing the monitor. Positioning / Ventilation x Avoid exposing the monitor to direct sunlight, stoves or any other heat sources. x To prevent overheating, make sure that the ventilation openings of the monitor are not covered. x Keep away from any magnetic objects, such as speakers, electric motors, transformers, . . . etc. x When positioning this monitor, make sure that the mains plug and socket are easily accessible. Pedestal With the built-in pedestal you can tilt and / or swivel the monitor for a most comfortable viewing angle. 107 E EXIT MENU 4 Connection Important: Please make sure the AC power to your computer is "OFF" before connecting or disconnecting any display peripheral. Failure to do so may cause serious personal injury as well as permanent damage to your computer equipments. · Connect the monitor to the computer using the supplied interface cables. Connection with computer system other than IBM PC may need different type of adapters. Please consult your computer supplier for these adapters. Connect the power cord to a wall outlet after the interface cable is properly connected. E N Monitor rear view 1) IBM PC connection 2) Mains connection WARNING:SHOCK HAZARD-DO NOT OPEN AVIS:RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO, NO ABRIR 2 1 5 E N Control locations and functions Monitor control panel EXIT MENU Descriptions of knobs and keypads on front control panel / / · Press this knob to switch ON and OFF of monitor's power · OSD rotary control knob. · Adjust contrast or the display. · Adjust brightness or the display. 6 On-Screen-Display Activating the On-Screen-Display The monitor controls are accessed by pressing button to enable OSD (On-Screen-Display). The main menu will be displayed as follows. E N H:68. 8KHz V:85Hz CONTRAST 70 Each Function is selected by highlighting it via the tact key and pressing button to confirm. To exit OSD, highlight press select button . , to select or adjust and While operating Function, please use press button to confirm. Note: If adjustment or selection of any OSD menu is not made for more than 10 seconds, the current setup will be saved and the OSD will disappear automatically. BRIGHTNESS & CONTRAST q Brightness : Adjusts background brightness. H:68. 8KHz V:85Hz BRIGHTNESS 70 7 E N q Contrast : Adjusts contrast between foreground and background. H:68. 8KHz V:85Hz CONTRAST 70 q EXIT : Save user adjustment and OSD disappear. SIZE & POSITION q Horizontal Size : Adjusts image width. H:68. 8KHz V:85Hz H-SIZE A A 70 q Horizontal Position : Moves image left or right. H:68. 8KHz V:85Hz H-CENTER A A 70 8 q Vertical Size : Adjusts image height. H:68. 8KHz V:85Hz E N V-SIZE A A 70 q Vertical Position : Moves image up or down. H:68. 8KHz V:85Hz V-CENTER A A 70 q EXIT : Save user adjustment and OSD disappear. GEOMETRY q Pincushion : Adjusts the amount of curvature on the vertical edges. H:68. 8KHz V:85Hz PINCUSHION A A 70 q Trapezoid : Equalizes the length of the top and bottom edges. H:68. 8KHz V:85Hz TRAPEZOID A A 70 9 E N q Rotation : Tilts the image clockwise or counter-clockwise. H:68. 8KHz V:85Hz ROTATION A A 70 q EXIT : Save user adjustment and OSD disappear. q PIN-BALANCE : Adjust picture curves outwards or inwards. H:68. 8KHz V:85Hz PIN BALANCE A A 70 q PARALLEL : Adjust for optimal parallelogram screen picture. H:68. 8KHz V:85Hz PARALLELOGRAM A A 70 COLOR TEMPERATURE q 9300°K : Factory preset color temperature of 9300°K. q 6500°K : Factory preset color temperature of 6500°K. H:68. 8KHz V:85Hz H:68. 8KHz V:85Hz RECALL 9300K COLOR TEMPERATURE RECALL 6500K COLOR TEMPERATURE 10 q User : User set for color temperature then select R, G for adjustment. [. . . ] 1 2 3 4 5 6 7 8 Assignment Red video input Green video input Blue video input Ground Identical output - Connected to pin 10 Red video ground Green video ground Blue video ground Pin No. 9 10 11 12 13 14 15 Assignment No pin Self-test Ground Serial data line (SDA) H. Sync (VCLK for DDC) Data clock line (SDA) 17 E N 17E4222E Digital AutoScan Colour Monitor Contents English Introduction Feature Highlights Safety precautions and maintenance Package End of life disposal Installation Connection Control locations and functions On-Screen-Display Data Storage Automatic Power Saving Specification . . . . 16 18 OTHER LANGUAGE VERSIONS FRENCH(FRANCAIS) . . . . [. . . ]