User manual PHILIPS 190CW7CS

[. . . ] Philips LCD Monitor Electronic User's Manual · Safety Precautions and Maintenance · FAQs · Troubleshooting · Regulatory Information · Other Related Information Safety and Troubleshooting Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your computer monitor: Operation: %Ï %Ï %Ï %Ï %Ï %Ï %Ï %Ï Keep the monitor out of direct sunlight and away from stoves or any other heat source. Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor's electronics. Do not block the ventilation holes on the cabinet. When positioning the monitor, make sure the power plug and outlet are easily accessible. [. . . ] There are two types of black dot defects: One dark sub pixel Two or three adjacent dark sub pixels Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables. BRIGHT DOT DEFECTS MODEL ACCEPTABLE LEVEL 190CW7 1 lit subpixel 2 adjacent lit subpixels 3 adjacent lit subpixels (one white pixel) Distance between two bright dot defects* Total bright dot defects of all types 3 1 0 >25mm 3 BLACK DOT DEFECTS MODEL 1 dark subpixel 2 adjacent dark subpixels 3 adjacent dark subpixels Distance between two black dot defects* Total black dot defects of all types ACCEPTABLE LEVEL 190CW7 5 2 0 15mm > 5 TOTAL DOT DEFECTS MODEL Total bright or black dot defects of all types Note: * 1 or 2 adjacent sub pixel defects = 1 dot defect Your Philips monitor is ISO13406-2 Compliant ACCEPTABLE LEVEL 190CW7 5 RETURN TO TOP OF THE PAGE Installing Your LCD Monitor · Front View Produt Description · Connecting to Your PC · The Base · Getting Started · Optimizing Performance Front View Product Description 1 2 3 4 5 6 AUTO MENU To switch monitor's power On and Off To access OSD menu / to confirm To move and adjust To adjust brightness of the display To adjust contrast of the display Automatically adjust the horizontal position, vertical position, phase and clock settings. RETURN TO TOP OF THE PAGE <> Rear View 1 2 3 4 Kensington anti-thief lock AC power input DVI-D input VGA input RETURN TO TOP OF THE PAGE Optimizing Performance %Ï For best performance, ensure that your display settings are set at 1440 x 900, 60Hz. Note: You can check the current display settings by pressing the 'MENU' button once. The current display mode is shown in OSD main controls called RESOLUTION. %Ï You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance out of your monitor. Step-by-step instructions are provided to guide you through the installtion process. Click on the link to know more about this program. More about FP_setup4. 3. exe RETURN TO TOP OF THE PAGE Connecting to Your PC · Front View Product Description · Accessory Pack Unpack all the parts. · Connecting to Your PC · Getting Started · Optimizing Performance · The base Accessory Pack Power cord VGA cable EDFU pack RETURN TO TOP OF THE PAGE Connecting to Your PC 1) Connect the power cord to the back of the monitor firmly. 2) Connect to PC (a) (b) (c) (d) Turn off your computer and unplug its power cable. Connect the monitor signal cable to the video connector on the back of your computer. Plug the power cord of your computer and your monitor into a nearby outlet. If the monitor displays an image, installation is complete. RETURN TO TOP OF THE PAGE The Base · Front View Product Description · Accessory Pack · Connecting to your PC · Getting Started · Optimizing Performance · Remove the Base %Ï Remove the Base Condition: for VESA standard mounting applications Remove the 3 screws and then remove the base from the LCD monitor. Note: This monitor accepts a 100mmx100mm VESA-Compliant mounting interface. RETURN TO TOP OF THE PAGE Your LCD Monitor : · Front View Product Description · Setting Up and Connecting Your Monitor · Getting Started · Optimizing Performance Getting Started Getting Started Use the information file ( . inf) for Windows® 95/98/2000/Me/XP or later The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for Windows® 95/98/2000/Me/XP. This information file ( . inf) should be installed in order that your Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 95/98/2000/Me/XP and the Plug & Play application can be activated. The installation procedure based on Windows® '95 OEM Release 2 , 98 , Me, XP and 2000 is specified as follows. For Windows® 95 1Start Windows® '95 . 2Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3Double click on the 'Display' Icon. 4Select the 'Settings' tab then click on 'Advanced. . . '. 5Select the 'Monitor' button, point to 'Change. . . ' then click on 'Have Disk. . . '. 6Click on the 'Browse. . . ' button, select the appropriate drive F: ( CD-ROM Drive) then click . on the 'OK' button. 7Click on the 'OK' button then select your monitor model and click on 'OK'. . For Windows® 98 1Start Windows® 98 . 2Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3Double click on the 'Display' Icon. 4Select the 'Settings' tab then click on 'Advanced. . . '. [. . . ] It also has hardware support for reset and suspend/resume signaling. The controller provides the interface registers to allow communication to/from the host. Hub specific status and control commands permit the host to configure a hub and to monitor and control its ports. Device A logical or physical entity that performs a function. [. . . ]