User manual PHILIPS 190TW8FB

[. . . ] Introduction Thank you for purchasing this television set. This handbook has been designed to help you install and operate your TV Monitor set. We would strongly recommend that you read it thoroughly. We hope our technology meets entirely with your satisfaction. EN FR NL DE IT ES PT CZ DK TR GR Table of Contents Important safety information . [. . . ] Source-IN AUDIO COMPOSITE S-Video R WY S-VIDEO SPDIF-OUT PC AUDIO-IN SCART AV HDMI Y WR Y R Yellow Red White DVD or VCR or STB W * Philips recommends the following priority for connection types: HDMI ->SCART -> AV TV-OUT SCART Recorder AV *SCART-out only works with analog broadcasts. 7 Connecting a camera, camcorder, video game or headphones Connect your camera, camcorder, video game console or headphones to the video/audio ports on the rear of the TV Monitor set as shown below. w w Y Y R R Connecting a PC or notebook computer To display PC output on your TV Monitor, connect your PC or notebook computer to the TV Monitor as shown below. SPDIF-OUT PC AUDIO-IN D-Sub D-Sub * For VGA input, Philips recommends setting your PC's external monitor resolution to 1440 x 900 pixels @ 60 Hz refresh rate. Selecting the input source Once you have connected your antenna or external equipment to the TV Monitor, you need to select the correct input source. Press the corresponding button on the remote control to select the correct input source. Input button guide: 1 2 3 4 TV key Toggle Analog TV (ATV) between input sources. AV key Toggle AV and HDMI between input sources. SCART key Toggle SCART between input sources. PC key Toggle VGA between input sources. 1 2 3 4 8 OSD navigation Many of the advanced settings and adjustments are available through using the OSD (onscreen display) menus, as shown in the example screenshot below. 22Mhz Germany Off Press the MENU key to bring up the OSD. Using the directional keys, select Channel management from the OSD. Use the directional keys to navigate the menus. The Channel management menu can be used to set the channel namings, Auto Scan, Manual Scan channel and other related settings. 2 3 4 Move Enter Back Adjusting the settings 1 Settin s g Menu Language Sleep Set PIN Wide Mode Factory Default Full English Off Press the MENU key to bring up the OSD. Using the directional keys, select Settings from the OSD. Then navigate to the feature you wish to adjust. The Settings menu can be used to adjust the menu language and other important settings. 2 3 Move Enter Back * The options available on the OSD may vary depending on the TV Monitor signal source. Advanced features Lock This Channel Lock This Channel allows you to enter a password and effectively stop anyone without the password from watching TV Monitor Channel. 10 To enable this feature: Setting a personal PIN Settings Menu Lang uag e Sleep Set PIN Wide Mode Factory Default English Off Full 1 Press the MENU key on the remote control to bring up the OSD. Move Enter Back 2 Use the directional keys to navigate to the Set PIN (see note) . Then select 3 Enter a four-digit password. Type it again and press OK to reconfirm. 4 Press MENU to exit. * The default PIN for this TV Monitor is "0000. " First enter "0000" when you want to change the PIN. If youforget your PIN, please enter 6163 to reset. Locking TV Channel Channel Management Country Skip Reorder Name Frequency Auto Scan Manual Scan Lock This Channel 639. 22Mhz Germany Off 1 Press the MENU key on the remote control to bring up the OSD. Move Enter Back 2 Use the directional keys to navigate to the . Then select Lock This Channel Channel Management menu. 3 Enter your PIN. Type it again and press OK to reconfirm. (see page 10 note) 11 Reorder for channels The first time you completed the setup wizard, all available channels were listed. If you need to reorder for new channels, please follow the steps below: Reordering for channels 1 Press the MENU key on the remote control to bring up the OSD. 2 Use the directional keys to navigate and select Channel Management. Channel Management Country Skip Reorder Name Frequency Auto Scan Manual Scan Lock This Channel 639. 22Mhz Germany Off 3 Highlight Reorder. [. . . ] The am plifier connected to the TV Monitor does not deliver any sound?Check that you have not confused the audio output with the audio input. Check that you have configured the computer on a compatible display resolution (see p. 8). No picture No sound PC mode don't work ? Remote control The TV Monitor set does not react to the remote control; the indicator on the set no longer flashes when you use the remote control?Standby If the set receives no signal for 30 mins, it automatically goes into standby mode. [. . . ]