User manual PHILIPS 2 HD LED CLOCK VCR VRZ223AT

[. . . ] VRZ223(H1690). QX33 4/9/99 9:09 AM Page 1 Video Cassette Recorder TM VRZ223AT Owner's Manual IMPORTANT! Return Your Warranty Registration Card Within 10 Days. See Why Inside. VRZ223(H1690). QX33 4/9/99 9:09 AM Page 2 Return your Warranty Registration card today to ensure you receive all the benefits you're entitled to. Once your PHILIPS MAGNAVOX purchase is registered, you're eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits. Warranty Verification Registering your product within 10 days confirms your right to maximum protection under the terms and conditions of your PHILIPS MAGNAVOX warranty. Owner Confirmation Your completed Warranty Registration Card serves as verification of ownership in the event of product theft or loss. Model Registration Returning your Warranty Registration Card right away guarantees you'll receive all the information and special offers which you qualify for as the owner of your model. S REG I ST RATION N Know these Dear PHILIPS MAGNAVOX product owner: Thank you for your confidence in PHILIPS MAGNAVOX. [. . . ] q WEEKLY: The VCR will record on the same day, at the same time, and for the same length of time every week. Daily Recording (example) DAILY PROGRAM (MON-FRI) PROGRAM -1 2 3 4 5 6 7 8- Helpful Hint · If you need to make a correction while programming a timer recording, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the correct information. SELECT PROGRAM NUMBER TO END PUSH EXIT VRZ223(H1690). QX33 4/9/99 9:09 AM Page 29 Timer Recording (cont'd) 29 Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear onscreen briefly. Information about the program in that slot will appear on-screen. If this happens, press the STATUS/EXIT button, then select another number. 4 4-7 POWER VCR TV EJECT 5 1 4 7 VCR PLUS+ 2 5 8 0 3 6 9 +100 VOLUME VCR/TV Use the Number buttons to enter the channel you want to record. q If you have a basic antenna or cable hookup (as shown on pages six-seven) enter the channel number of the TV program you want to record. (Enter a 0 before all single-digit channels. ) q If you are recording from line input, press 0, 0. q If you are using a Cable Box/DBS, enter the Cable Box/DBS output channel (03 or 04). Set the Cable Box/DBS to the channel you want to record. Leave the Cable Box/DBS on for the timer recording. See page eight for details. ONE TIME PROGRAM PROGRAM 1 CHANNEL ­­ CHANNEL SPEED MUTE MENU STATUS/EXIT CLEAR MEMORY REWIND /PLAY F. FWD REC/OTR /STOP PAUSE/STILL TO CORRECT PUSH CLEAR TO END PUSH EXIT 6 Press two Number buttons for the hour you want the recording to begin. Press two Number buttons for the minute you want the recording to begin. For example, for 9:30 PM, press 09, 30, 2. ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON ­­:­­ TO CORRECT PUSH CLEAR TO END PUSH EXIT 7 Follow the instructions in step 6 to enter the recording's stop time. (AM or PM will be set automatically. ) ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF ­­:­­ TO CORRECT PUSH CLEAR TO END PUSH EXIT Helpful Hint · Entries that do not match the VCR's clock or calendar will cause a question mark to appear on-screen. Instructions continue on page 30. VRZ223(H1690). QX33 4/9/99 9:09 AM Page 30 30 Timer Recording (cont'd) 8 Press the Number 1 button to record in SP speed, the Number 2 button to record in LP speed, or the Number 3 button to record in SLP speed. (See the chart below. ) You cannot use the SPEED button at this time. ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP SP=1 LP=2 SLP=3 TO CORRECT PUSH CLEAR TO END PUSH EXIT 11 POWER VCR TV EJECT 1 4 2 5 8 0 3 6 9 +100 VOLUME VCR/TV 8 10 9 Press two Number buttons for the month and two Number buttons for the day you want to record the program. For example, for July 10, 1998, press 07, 10. The day of the week and the year will appear automatically (you cannot program the VCR to record more than one year in advance). ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP START DATE 07/10/98 FRI. TO CORRECT PUSH CLEAR TO END PUSH EXIT 9 7 VCR PLUS+ CHANNEL SPEED MUTE MENU STATUS/EXIT CLEAR MEMORY REWIND /PLAY F. FWD REC/OTR /STOP PAUSE/STILL Press the STATUS/EXIT button. PROGRAM WAS COMPLETED / PLEASE TURN OFF VCR FOR TIMER RECORDING will appear on-screen briefly. (If PROGRAM NOT COMPLETED appears, try again from step 1. ) 10 11 Turn off the VCR power. The Timer light will appear on the display panel. [. . . ] This includes, but is not limited to, prerecorded material, whether copyrighted or not copyrighted. ) · damage caused by the use of non-VHS tapes or tapes that have not been tested and labeled for use in two, four, six, and eight hour VHS recorders. · a product that is used for commercial or institutional purposes (including but not limited to rental purposes). Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics Company. In countries where Philips Consumer Electronics Company does not distribute the product, the local Philips service organization will attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not readily available). [. . . ]