User manual PHILIPS 200P3G-00C

[. . . ] Consult a service technician if the monitor does not operate normally when you have followed the instructions in this manual. The casing cover should be opened only by qualified service personnel. Keep the monitor out of direct sunlight and away from stoves or any other heat source. Remove any object that could fall into the vents or prevent proper cooling of the monitor's electronics. [. . . ] It may not work properly if using nonstandard PC or video card. Imaging Problems Press the Auto button. Adjust the image position using the Horizontal Position and/or Vertical Position in OSD Main Controls. q q Display position is incorrect q Image vibrates on the screen Check that the signal cable is properly connected to the graphics board or PC. file:///D|/My%20documents/dfu/J/english/200p4/safety/saf_troub. htm (1 of 3) [4/15/2004 1:45:09 PM] Troubleshooting Vertical flicker appears q q Press the Auto button. Eliminate the vertical bars using the Clock Adjustment of VIDEO NOISE in OSD Main Controls. Horizontal flicker appears q q Press the Auto button. Eliminate the horizontal bars using the Phase Adjustment of VIDEO NOISE in OSD Main Controls. q The screen is too bright or too dark Adjust the contrast and brightness on OSD Main Controls. (The backlight of the LCD monitor has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer). q An after-image appears If an image remains on the screen for an extended period of time, it may be imprinted in the screen and leave an after-image. This usually disappears after a few hours q An after-image remains after the power has been turned off. This is characteristic of liquid crystal and is not caused by a malfunction or deterioration of the liquid crystal. The after-image will disappear after a peroid of time. q Green, red, blue, dark, and white dots remains The remaining dots are normal characteristic of the liquid crystal used in today's technology. For further assistance, refer to the Consumer Information Centers list and contact your local Philips distributor. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/J/english/200p4/safety/saf_troub. htm (2 of 3) [4/15/2004 1:45:09 PM] Troubleshooting file:///D|/My%20documents/dfu/J/english/200p4/safety/saf_troub. htm (3 of 3) [4/15/2004 1:45:09 PM] Regulatory Information ·TCO'99 Information ·TCO'99 Environmental Requirements ·TCO'03 Information ·Recycling Information for Customers CE Declaration · of Conformity Energy Star · Declaration ·Federal Communications Commission (FCC) Notice (U. S. Only) ·Commission Federale de la Communication (FCC Declaration) ·EN 55022 Compliance (Czech Republic Only) ·VCCI Class 2 Notice (Japan Only) ·MIC Notice (South Korea Only) ·Polish Center for Testing and Certification Notice ·North Europe (Nordic Countries) Information ·BSMI Notice (Taiwan Only) ·Ergonomie Hinweis (nur Deutschland) ·Philips End-ofLife Disposal Regulatory Information TCO '99 Information Congratulations!You have just purchased a TCO '99 approved and labeled product!Your choice has provided you with a product developed for professional use. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the color-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labeled unit. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. [. . . ] Vedia 3892 Capital Federal CP: 1430 Buenos Aires Phone: (011)-4544 2047 BRASIL Philips da Amazônia Ind. Luis Carlos Berrini, 1400 - Sao Paulo -SP Phone: 0800-701-0203 CHILE Philips Chilena S. A. box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S. A. -Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone:(01)-8000 111001 (toll free) Fax : (01)-619-4300/619-4104 MEXICO Consumer Information Centre Norte 45 No. 669 Col. [. . . ]