User manual PHILIPS 20I LCD TV 20FT3010-37B

[. . . ] DFU 20FT3010/37 050404. 0944 PRELIMINARY PRELIMINARY 20FT3010/37 Institutional Television www. itv. philips. com Directions For Use 20" LCD Monitor with iFace and Philips ITV SmartPort for health care applications Pillow speaker / pendant control interface Pillow speaker / pendant control (not included) (rear view of unit) Philips SmartPlug TM lmtb 1 P DFU 20FT3010/37 050404. 0944 PRELIMINARY IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] The current channel ring can also be selected by means of the RESET button on the setup remote (when the setup remote is in setup mode). ________________________________________________________________________________________________ SWITCH ON CHANNEL* (STANDARD/AV1/ AV1YC/ AV2/AV2YC/CVI/TV 1-125) SETUP x CONSUMER FEATURES MENU_ Applicable to / available in Commercial Mode / setup menu only. If SWITCH ON CHANNEL is set to STANDARD, the channel to which the television will be adjusted at power-on will be the last channel / input to which it was tuned when the television was last powered off. If SWITCH ON CHANNEL is set to a particular input or channel, that will be the input or channel to which the television will be tuned at power-on. Note: AV1YC / AV2 / AV2YC are not applicable to the 20FT3010/37. ________________________________________________________________________________________________ SETUP x CONSUMER FEATURES MENU_ POWER ON* (STANDARD / FORCED) Applicable / available only to the Commercial Mode / setup menu. When POWER ON is set to FORCED, the television will automatically power-up whenever it is supplied with mains power. With POWER ON set to FORCED, the television will remain powered on long as mains power is applied, and cannot be turned off with a guest-mode remote, or with the television's keyboard (even if the keyboard is not locked out). When POWER ON is set to STANDARD, the television will remain in standby mode (i. e. off) when AC power is applied or resumed, until the unit is powered on. ________________________________________________________________________________________________ SETUP x CONSUMER FEATURES MENU_ CHANNEL DISPLAY* (NUMBER / LABEL / ALL / NONE) Applicable to / available in Commercial Mode / setup menu only. CHANNEL DISPLAY determines the channel information (NUMBER and / or LABEL), if any, that is displayed briefly whenever the channel is changed. ________________________________________________________________________________________________ SETUP x CONSUMER FEATURES MENU_ KEYBOARD LOCK* (OFF / ON) Applicable to / available in Commercial Mode / setup menu only. If KEYBOARD LOCK is set to ON, the television will not respond to commands from its local keyboard (power, channel, volume, etc. ). When KEYBOARD LOCK is set to ON, the television responds to commands from its local keyboard (power, channel, volume, etc. ) ________________________________________________________________________________________________ SETUP x CONSUMER ESP* (OFF / 1 - 99) FEATURES MENU_ Applicable / available only to the Commercial Mode / setup menu. ESP (Energy Savings Programmability), if not OFF, determines the number of hours (1 - 99) the television will remain powered on after the most recent front panel keyboard or remote control command. NOTE: If POWER ON (see POWER ON STANDARD / FORCED) is set to FORCED, ESP has no effect. ________________________________________________________________________________________________ WELCOME MESSAGE* (>) SETUP x CONSUMER FEATURES MENU_ Applicable / available only to the Commercial Mode / setup menu. The WELCOME MESSAGE feature makes it possible for an on-screen message to appear whenever the television is first turned on. The message will remain until any frontpanel keyboard command or remote control command is received. The WELCOME MESSAGE sub-menu is shown below. WELCOME MESSAGE MESSAGE LINE 1 LINE 2 CLEAR EXIT OFF / ON (20 CHARACTERS) (20 CHARACTERS) > > Use cursor-up and cursor-down to select the WELCOME MESSAGE sub-menu item. While Line 1 or Line 2 of the WELCOME MESSAGE message is highlighted, use cursor-left and cursor-right to enter and exit message-edit mode and position the cursor within the line of the message content. [. . . ] · reception problems caused by signal conditions or cable or antenna systems outside the unit. · a product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications. · incidental or consequential damages resulting from the product. (Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. [. . . ]