User manual PHILIPS 20PV164

[. . . ] Select the Confirm with the required function with the D and the C buttons. OK button. & Programming with 'VIDEOPlus+' All the information required for programming is encoded in the 'VIDEOPlus+' code. 1 2 Selecting a TV channel Select the required TV channel (= programme number) with the P p button or the 0-9 buttons on the remote control. The selected programme number (e. g. : 'P 01' ) appears in the upper right corner of the TV screen. Press the SV/V+ button on the remote control. Enter the entire 'VIDEOPlus+ code'. This code (up to 9 digits) is found next to the start time of a TV programme in your TV guide. [. . . ] Press the menu simultaneously. buttons D and button. Press the menu simultaneously. 2 Select and confirm the line 'AUTO STORE' . 2 Select and confirm the line 'SORT' . The 'Automatic channel search' function starts. SORT AUTO STORE PRESS x y TO STOP SEARCH PLEASE WAIT CHANNELS FOUND: aaabbbbbbbbbbbbbbbbb 1 FROM TO STORE vw C-21 P01 P02 3 On the TV screen, in the line 'FROM' , select the TV 3 Wait until all TV channels have been stored. All TV channels will be stored from programme number 1 upward. How to search for a TV channel manually, you can read in chapter 4 'SPECIAL FEATURES' in the section 'Manual channel search'. Note: Automatic Channel Installation (ACI), only for sets with TELETEXT: Some cable companies or broadcasters offer the possibility to install TV channels automatically with 'ACI'. Information about the installation offered and how to select it, will appear in the display. This set will recognize and install TV channels with 'ACI' automatically. TV channels will be stored from programme number 1 onward. If 'ACI' cannot identify a TV channel, you can search for it using the method as described in the section 'Manual channel search'. * If the 'Automatic channel search' function is activated, any previously programmed TIMER blocks will be cleared. You can store up to 69 TV channels. channel to which you want to allocate a programme number, e. g. : 'P 01' . 4 In the line 'TO' , select the required programme number, e. g. : 'P 02' . 5 Select and confirm the line 'STORE' . The allocated TV channels will be exchanged. 6 Repeat steps 3to 5until you have allocated a pro- gramme number to all the required TV channels. To finish, press the MENU button twice. 4 2. PLAYBACK Tape position/Index search I 1 Insert a cassette into the cassette slot. Select the 'LP' (=LongPlay) recording speed and stop by pressing the MENU button. During playback the TV Combi will automatically select the correct playback speed. 'VPS' (Video Programming System)/ 'PDC' (Programme Delivery Control) With 'VPS/PDC', the TV station controls the start and the duration of a programmed recording. This means that the video recorder switches itself on and off at the right time even if a TV programme you have programmed begins earlier or finishes later than expected. Usually the start time is the same as the 'VPS/PDC' time. If, however, a different 'VPS/PDC' time is given, e. g. : '20. 15 (VPS/PDC 20. 14)', you have to enter '20. 14' (the 'VPS/PDC' time) exactly to the minute. If you are not using 'VPS/PDC', the 'VPS/PDC' indication must be off. · · · · · 6 Programming with 'VIDEOPlus+' All the information required for programming is encoded in the 'VIDEOPlus+' code. 1 Press the SV/V+ How to enter, check or clear a TIMER block manually 1 Press the TIMER k button. button on the remote control. 2 Select a free TIMER block or the TIMER block you want 2 Enter the entire 'VIDEOPlus+ code'. This code (up to 9 to check or clear. 3 Clear: Press the CLEAR digits) is found next to the start time of a TV programme in your TV guide. If you entered an incorrect code number, clear it with the CLEAR button. button. D 4 Enter/Check: Press the VIDEOPLUS CODE DAILY/WEEKLY PROGRAMME NR. or C button to switch between 'DATE' (date), 'DW' (daily, weekly), 'PR' (programme number), 'START' (start time) and 'END' (end time). Press the A and the B , or the 0-9 buttons to change the data. MENU ONCE 01 5 To end programming, press the OK button. x y 0-9 6 Press the STANDBY m button. 3 If you want to repeat programming at daily or weekly intervals, select the required setting in the 'DAILY/WEEKLY' line. 'Daily' programming can only be used for recordings to be made from Mondays to Fridays inclusive. 4 After the confirmation the corresponding data appears on Important notes for programmed recordings · If the message 'PLEASE PRESS STOP' or 'PLEASE PRESS STANDBY' appears on the TV screen, press the STOP h or the STANDBY m button. A TIMER recording will function only, if the set isn't used for other video recorder functions (e. g. : playback). [. . . ] 4 Determine the time you wish the set to switch on. 5 Select the 'WAKE UP' line and switch the 'on-timer' on or 3 Select the 'SEARCH' line. 4 Press the button as often as necessary, until you have found the right TV channel. C off. 6 Press the MENU button. Child lock 1 Press the MENU button. 2 Select and confirm the 'FEATURES' line. 3 Select the 'CHILD LOCK' line. [. . . ]