User manual PHILIPS 25CE6270-07B

[. . . ] Just put the threaded end of the cable signal to the TV's antenna plug and screw it down finger tight. 2 Cable TV Signal Input Cable TV Company 75 Monitor out AV1 in COMPONENT VIDEO INPUT AV2 in 75 VIDEO L/ Mono AUDIO R Y S-VIDEO Pb Pr OR NOTE: The connecting cable for the Converter is supplied from the Cable TV Company. Cable TV Converter Box Connection IN OUT Back of TV Round Cable 75 Ohm 1 Note: For homes with separate UHF and VHF antennas you will need an optional combiner to connect to the TV. U/V Combiner ANTENNA COMBINATION UHF/VHF A combination antenna receives normal broadcast channels (VHF 2-13 and UHF 14-69). Your connection is easy since there is only one 75 (ohm) antenna plug on the back of your TV - and that's where the antenna goes. If your antenna has a round cable (75 ohm) on the end, then you're ready to connect it to the TV. [. . . ] Remove the battery compartment lid on the back of the remote. Place the batteries (2- AA) in the remote. Be sure the (+) and (-) ends of the batteries line up correctly (inside of case is marked). Slide the TV/VCR/ACC switch to the TV position on the remote control, then point the remote at the remote sensor window when operating the TV with the remote control. POWER button - Press the Power button to turn the TV on or off. Battery Compartment Lid 4 VOL TV/VCR/ACC MODE SWITCH The remote's TV/VCR/ACC Switch controls how buttons on the remote are used. For example: With the switch in the "TV" position: the Menu, CURSOR , , and s buttons are used to select and adjust on-screen TV features. With the switch in the "ACC" position: the Power, Channel Number, and Channel Up (+) /Down (­) buttons on the remote work with Cable TV Converters. With the switch in the "VCR" position: the Menu, CURSOR , , and s buttons on the remote work Stop, Play, Fast Forward, and other VCR features. Note: For more details on how the TV remote works with VCRs and Cable Converters, see the other owner's manual supplied with your TV. QUADRA SURF Buttons - (Red, Green, Yellow, Blue) Allows you to store and surf up to 10 channels you choose for each colored button. SMILEY Button - Press to add channels in the "Quadra Surf" lists. TV/VCR/ACC MODE SWITCH - Slide to position of TV to control TV functions, VCR to control VCR functions and ACC for Cable Converter, DBS, DVD, etc. , functions. CH(annel) + or ­ Buttons - Press to select channels in ascending or descending order. SLEEP Button - Press the Sleep button to set the TV to automatically turn itself off after a set period of time. Press repeatedly to select 15, 30, 45, 60, 90, 120, 180 or 240 minutes. PAUSE Button - Press to pause the viewing of a prerecorded video tape. The picture will freeze on the screen until the Play or Pause buttons are pressed again. NUMBERED (0-9) Buttons - Press the numbered buttons to select TV channels or to enter certain values within the on-screen menu. For single channel entries, press the numbered button for the channel you desire. The TV will pause for a second or two before changing to the chosen channel. A/CH Button - (Alternate Channel) Press to toggle between the last view channel and the channel presently being viewed. VOL SMART HELP Just a couple of reminders about the STATUS/EXIT button; you can press the STATUS/EXIT button (on the remote) to see what channel the TV is ON, what sound mode (stereo or mono) is present or to remove the on-screen menu from the TV's screen at any time. · 2 SETTING UP YOUR TELEVISION FOR THE FIRST TIME MENU F eatures for your television can be adjusted from within a MENU shown on the TV's screen. A MENU is nothing more than an onscreen list of features. Some of the features have submenus but each MENU item can be adjusted or activated (deactivated) by viewing the screen and simply pressing the proper button. Press the MENU button on the remote or the Install/Menu buttons (Volume +, ­) on the TV simultaneously to show the on-screen menu. Press the CURSOR UP or DOWN s buttons on the remote (or the Volume +, ­ buttons on the TV) to pick any of the on-screen menu features. Press the CURSOR RIGHT or LEFT buttons on the remote (or Channel or buttons on the TV) to adjust any highlighted on-screen feature. Picture Menu Sound Menu Features Menu Main Picture Sound Features Install Press the STATUS/EXIT button on the remote to clear the menu from the screen after an adjustment. [. . . ] Press CURSOR UP or DOWN s buttons to scroll the Install features until the words TUNER MODE is highlighted Press the CURSOR RIGHT button to select either ANTENNA, CABLE, or AUTO mode. Press the CHANNEL (+), (­) buttons and see which channels have been added to the TV's memory. If you want to delete any unwanted channels from the TV's memory, refer to the section on adding and removing channels (Channel Edit) below. CHANNEL EDIT C hannel Edit makes it easy for you to ADD or DELETE channels from the list of channels stored in the TV's memory. Press the MENU button on the remote to show the on-screen menu. Press the CURSOR UP or DOWN s buttons to scroll through the on-screen menu until the word INSTALL is highlighted. [. . . ]