User manual PHILIPS 26PW6341

[. . . ] Place the batteries (2-AA) in the remote. Be sure the (+) and (­) ends of the batteries line up correctly (the inside of the case is marked). Reattach the battery compartment door. Battery Compartment Door 1 2 3 Be sure to point the remote at the Remote Sensor window on the front of the television when using the remote control to operate the television. 2 "AA" Batteries Battery Compartment REMOTE CONTROL BUTTONS QUADRA SURF Buttons - (Red, Green, Yellow, Blue) Allows you to store and surf up to 10 channels you choose for each colored button. SMILEY Button - Press to add channels in the "Quadra Surf" lists. [. . . ] CC Button - Press to activate the Closed Captioning options. Repeatedly press the CC button with scroll the options available on the TV screen. DEMO VOL CLOCK POWER Button - Press the Power button to turn the TV on or off. FROWNIE Button - Allows you to delete stored channels within the "Quadra Surf" lists for the colored buttons. AUTO PICTURE Button - Press repeatedly to choose from 5 different factory pre-defined picture settings. Choose from Personal (how you set the Picture Menu adjustment controls), Movies (when watching movies), Sports (for any sporting event), Weak Signal (used when the signal being received is not the best) or Multimedia (when playing video games). STATUS/EXIT Button - Press to display the current channel number. If the onscreen menu is displayed, press the Status/Exit button will remove it from the TV's screen. CURSOR , , , or Buttons - Press to navigate, select and adjust controls within the onscreen menu after the Menu button is pressed. These buttons also can be used with a VCR and when the TV/VCR/ACC Switch is in the VCR position. Press the to PLAY , REWIND , FAST FORWARD , or STOP the viewing of a prerecorded video tape. Also use the CURSOR UP or DOWN to "nudge" the picture up or down when using different screen formats, except widescreen. Once tuned, change channels at the cable box, not the television. 6 Monitor out AV1 in AV2 in VIDEO Y L/Mono Pb S-VIDEO R Pr COMPONENT VIDEO INPUT 5 AUDIO Jack Panel Back of TV ANT 75 Monitor out AV1 in AV2 in VIDEO Y L/Mono Pb S-VIDEO R Pr COMPONENT VIDEO INPUT AUDIO ANTENNA TV Antenna Connection: Outdoor or Indoor Antenna (Combination VHF/UHF) The combination antenna receives normal broadcast channels 2-13 (VHF) and 14-69 (UHF). A combination antenna receives normal broadcast channels (VHF 2­13 and UHF 14­69). Your connection is easy because there is only one 75 (ohm) antenna plug on the back of your TV, and that's where the antenna goes. 1 2 If your antenna has a round cable (75 ohm) on the end, then you're ready to connect it to the TV. If your antenna has flat, twin-lead wire (300 ohm), you first need to attach the antenna wires to the screws on a 300- to 75-ohm adapter. Push the round end of the adapter (or antenna) onto the 75 (ohm) plug on the back of the TV. If the round end of the antenna wire is threaded, screw it down finger tight. Twin Lead Wire 1 300 to 75-ohm Adapter 2 ANT 75 Monitor out AV1 in AV2 in VIDEO Y L/Mono Pb S-VIDEO R Pr COMPONENT VIDEO INPUT AUDIO Round 75 Coaxial Cable from Antenna Jack Panel Back of TV 2 HOOKING AV1 & AV2 INPUTS 24 SVHS UP THE TV T he TV's audio/video input jacks are for direct picture and sound connections between the TV and a VCR (or similar device) that has audio/video output jacks. Both the AV1 and AV2 Input Jack connections are shown on this page, but either one can be connected alone. Follow the easy steps below to connect your accessory device to the AV1 and AV2 in Jacks located on the back of the TV. Connect the VIDEO (yellow) cable to the VIDEO AV1 in (or AV2 in) jack on the back of the TV. Connect the AUDIO (red and white) cables to the AUDIO (left and right) AV1 in (or AV2 in) jacks on the rear of the TV. Connect the VIDEO (yellow) cable to the VIDEO OUT jack on the back of the VCR (either one or two) or accessory device being used. Connect the AUDIO (red and white) cables to the AUDIO (left and right) OUT jacks on the rear of the VCR (either one or two) or accessory device being used. [. . . ] Follow the instructions on how to tune to the AV 1 channel to view a pre-recorded tape. The following steps allow you to connect a second VCR to record the program while your watching it. Second VCR Connection/Recorder 3 VIDEO CABLE (Yellow) ANTENNA OUT OUT OUT Monitor OUT VIDEO &AUDIO L(eft) and R(ight) JACK PANEL Located on the back of the TV 3 4 5 A Connect one end of the yellow Video Cable to the Monitor out VIDEO plug. Connect the other end to the VIDEO IN plug on the second VCR. Connect one end of the red and white Audio cable from the Monitor out AUDIO L and R plugs on the TV to the AUDIO IN plugs on the VCR. [. . . ]