User manual PHILIPS 27CE3290

[. . . ] Place the batteries (2-AA) in the remote. Be sure the (+) and (­) ends of the batteries line up correctly (the inside of the case is marked). Reattach the battery compartment door. Battery Compartment Door 1 2 3 Be sure to point the remote at the Remote Sensor window on the front of the television when using the remote control to operate the television. 2 "AA" Batteries Battery Compartment REMOTE CONTROL BUTTONS QUADRA SURF Buttons - (Red, Green, Yellow, Blue) Allows you to store and surf up to 10 channels you choose for each colored button. SMILEY Button - Press to add channels in the "Quadra Surf" lists. [. . . ] CC Button - Press to activate the Closed Captioning options. Repeatedly press the CC button with scroll the options available on the TV screen. VOL POWER Button - Press the Power button to turn the TV on or off. FROWNIE Button - Allows you to delete stored channels within the "Quadra Surf" lists for the colored buttons. AUTO PICTURE Button - Press repeatedly to choose from 4 different factory pre-defined picture settings. Choose from Personal (how you set the Picture Menu adjustment controls), Movies (when watching movies), Sports (for any sporting event), or Weak Signal (used when the signal being received is not the best). STATUS/EXIT Button - Press to display the current channel number. If the onscreen menu is displayed, press the Status/Exit button will remove it from the TV's screen. CURSOR , , , or Buttons - Press to navigate, select and adjust controls within the onscreen menu after the Menu button is pressed. These buttons also can be used with a VCR and when the TV/VCR/ACC Switch is in the VCR position. Press the to PLAY , REWIND , FAST FORWARD , or STOP the viewing of a prerecorded video tape. Also use the CURSOR UP or DOWN to activate or deactivate the EXPAND 4:3 screen formatting control. CH(annel) + or ­ Buttons - Press to select channels in ascending or descending order. If your antenna has flat, twin-lead wire (300 ohm), you first need to attach the antenna wires to the screws on a 300- to 75-ohm adapter. Push the round end of the adapter (or antenna) onto the 75 (ohm) plug on the back of the TV. If the round end of the antenna wire is threaded, screw it down finger tight. Twin Lead Wire 1 300 to 75-ohm Adapter 2 ANT 75 Monitor out AV1 in AV2 in VIDEO Y L/Mono Pb S-VIDEO R Pr COMPONENT VIDEO INPUT AUDIO Round 75 Coaxial Cable from Antenna Jack Panel Back of TV 2 HOOKING AV1 & AV2 INPUTS 24 UP THE TV T he TV's audio/video input jacks are for direct picture and sound connections between the TV and a VCR (or similar device) that has audio/video output jacks. Both the AV1 and AV2 Input Jack connections are shown on this page, but either one can be connected alone. Follow the easy steps below to connect your accessory device to the AV1 and AV2 in Jacks located on the back of the TV. 1 SVHS 3 AV1 in AV2 in Monitor out AV2 VIDEO Y CVI BACK OF TV L/Mono Pb S-VIDEO AUDIO 1 2 3 4 5 6 7 Connect the VIDEO (yellow) cable to the VIDEO AV1 in (or AV2 in) jack on the back of the TV. Connect the AUDIO (red and white) cables to the AUDIO (left and right) AV1 in (or AV2 in) jacks on the rear of the TV. Connect the VIDEO (yellow) cable to the VIDEO OUT jack on the back of the VCR (either one or two) or accessory device being used. Connect the AUDIO (red and white) cables to the AUDIO (left and right) OUT jacks on the rear of the VCR (either one or two) or accessory device being used. Turn the VCR (either one or two) or accessory device and the TV ON. Press the CH + or ­ buttons on the remote control to select the AV1 channel for accessory device number one, or the AV2 channel for accessory device number two. AV1 or AV2 will appear in the upper left corner on the TV screen depending on the channel chosen. [. . . ] The following steps allow you to connect a second VCR to record the program while your watching it. Second VCR Connection/Recorder 3 VIDEO CABLE (Yellow) ANTENNA IN OUT OUT Monitor OUT VIDEO &AUDIO L(eft) and R(ight) JACK PANEL Located on the back of the TV 3 4 5 A Connect one end of the yellow Video Cable to the Monitor out VIDEO plug. Connect the other end to the VIDEO IN plug on the second VCR. Connect one end of the red and white Audio cable from the Monitor out AUDIO L and R plugs on the TV to the AUDIO IN plugs on the VCR. Turn the Second VCR ON, insert a black VHS tape and it's ready to record what's being viewed on the TV screen. Monitor out AV1 in AV2 in OUT OUT ANTENNA IN ANTENNA OUT VIDEO L AUDIO R VIDEO Y L/Mono R AUDIO L VIDEO ANTENNA OUT IN IN 5 AUDIO CABLES (Red & White) SECOND VCR AUDIO Pb S-VIDEO IN IN R Pr COMPONENT VIDEO INPUT 4 Jack Panel located on the Side of TV FIRST VCR (accessory device) (Hookup from AV1 on previous page. ) SIDE AUDIO/VIDEO INPUTS udio and Video Side Inputs are available for a quick connection of a VCR, to playback video from a camera or attach a gaming device. [. . . ]