User manual PHILIPS 27HT4000D/27B

[. . . ] __________________________ For Customer Use TABLE OF CONTENTS Introduction Safety Information . 5 Basic Installation/Functions Basic TV Connections . 9 TV Installation Activating TV Setup Menu . 12 - 19 Cabinet Dimension Drawings 27HT4000D Dimensions . [. . . ] If INCREDIBLE STEREO is set to SPATIAL, the sound from the TV will be specially processed with audio spatializer algorithms, resulting in a "3D stereo-like" effect. If INCREDIBLE STEREO is set to DOLBY VIRTUAL, the sound from the TV will be specially processed with patented Dolby audio algorithms, resulting in a "3D stereo surround" effect that conforms to the acoustic performance level as specified by Dolby. * ULTRA BASS (NO / YES) When ULTRA BASS is set to YES, the audio frequency equalization is modified such that the bass frequencies are significantly emphasized. * VOLUME BAR (NO / YES) When VOLUME BAR is set to YES, an OSD graphic appears providing visual verification (eg. "||||||||----15") of volume adjustments made with the remote control or the front panel of the TV. 14 TV SETUP MENU & SUB-MENUS (CONTINUED) · MIN VOLUME (||||||||||||| 0 - 63) 63) Specify the lowest volume setting possible by using the remote control or the TV front panel (if it is not locked out). This setting cannot exceed the MAX VOLUME. · MAX VOLUME (||||||||||||| 0 - 63) 63) Specify the highest volume setting possible by using the remote control or the TV front panel (if it is not locked out). This setting cannot be less than the MIN VOLUME. · SWITCH ON VOLUME (STANDARD / ||||||||||||| 0 - 63) 63) Specify the volume setting that takes effect when the TV is powered on. If STANDARD, the volume at power-on will be the volume at which the TV was prior to last power-down. If specified as 0 - 63, that will always be the volume at power-on, until SWITCH ON VOLUME is changed. · SWITCH ON CHANNEL (STANDARD / TV 1 - 125 / AV2 / SIDE / S-VIDEO / CVI) ) Specify the channel which the TV will be tuned when it is powered on. If STANDARD, the channel at power-on will be the same as the channel when the TV was tuned at last power-down. NO : The signals that are present at the monitor outputs are the same as those of the currently selected channels or video input. The monitor outputs "track" what is viewed and heard on the TV. YES : Regardless of the current selected TV source (eg. AV2, S-VIDEO, CVI) input, the signal present at the monitor outputs is always the tuner output (see NOTE below). Note : When The MONITOR OUT RF is initially changed from its current setting, the monitor out signal depends upon the previous MONITOR OUT setting until a different TV source is selected. From then on, the new MONITOR OUT setting will perform as described. 15 TV SETUP MENU & SUB-MENUS (CONTINUED) · WELCOME MESSAGE ( ) (>) A welcome message (maximum of 20 characters, 2 lines) can be programmed to appear on the TV screen when the TV is powered on. The message remains on the screen until any button on the TV front panel or remote control is pressed. This is how to set the Welcome Message : When the WELCOME MESSAGE setup menu is highlighted. Press cursor Æ or Í on the remote control to invoke the WELCOME MESSAGE sub-menu. WELCOME MESSAGE DISPLAY LINE 1 LINE 2 CLEAR NO / YES PHILIPS > INSTITUTIONAL TV > > 1 2 3 4 Press cursor Î or ï on the remote control to select the desired MESSAGE sub-menu item (eg. When DISPLAY is highlighted, press cursor Æ or Í on the remote control to select YES or NO. When YES is selected, WELCOME MESSAGE is enabled. Note : If Welcome Message is enabled but both LINE 1 and LINE 2 are blank (or consist entirely of space characters), no message will appear. [. . . ] All parts, including repaired and replaced parts, are covered only for the original warranty period. When the warranty on the product expires, the warranty on all replaced and repaired parts also expires. Your warranty does not cover: · labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. · product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips Consumer Electronics Company. [. . . ]