User manual PHILIPS 27PT91S

[. . . ] (See the "Tuner Mode A/B" section on page 3. ) Your TV can set itself to select only the channel numbers on your cable system (see "Auto Program" on page 3). If you use a cable converter box, set the TV to the same channel as the converter's CH 3/4 switch (on the back of the converter). Contact your dealer, or call our Parts Information Center at 1-800-851-8885 to order the following accessories: Two-way signal splitter Combination VHF/UHF Antenna Back of TV - Outdoor or Indoor Antenna Receives normal broadcast channels 213 (VHF) and 1469 (UHF). Round Cable 75 (Ohm) 8 8 M-Link PIP ANT "B" 75 +R L+ SURROUND SOUND Monitor out AV1 in AV2 in ANT "A" 75 VIDEO Y L/Mono Pb AUDIO R S-VIDEO Pr 1 OR OPTIONAL TWO-WAY SIGNAL SPLITTER (single, 75-ohm input to twin, 75-ohm outputs optional RF coaxial connecting cables also required) 2 PIP ANT "B" 75 ANT "A" 75 PIP ANT(enna) B Input 8 8 M-Link +R L+ 300 (ohm) to 75 (ohm) adapter Combination VHF/UHF antenna. SURROUND SOUND Monitor out VIDEO Y L/Mono Pb AUDIO R AV1 in AV2 in 3 S-VIDEO Pr ANT(enna) A Input NOTE: Proper operation of your TV is not dependent upon connection of the PIP ANT B input. [. . . ] Choose 15, 30, 45, 60, 90, 120, 180, or 240 minute before the TV will automatically turn off. Press to operate Picture-In-Picture features. See the PIP section in the Instructions for Use manual for details. Light Button Press to back-light the buttons on the remote control. TV/VCR (A/CH) Button TV/VCR Press while in the VCR mode (the VCR indicator on the front of the VCR will light) to view the playback of a tape. Press again to place in the TV position (the VCR indicator light will go off) to view one program while recording another program. A/CH Press to toggle between the currently viewed channel and the previously viewed channel. SLEEP POWER Number Buttons Press the number buttons to select TV channels. When selecting single-digit channels, press the number of the desired channel. The TV will pause for a few seconds and then tune to the selected channel. (Note: You can press 0, then the number also. ) For channels 100 and above, first press 1 then the next two numbers of the desired channel. PIP TV/VCR A/CH SWAP SOURCE UP PIP CH DN ON/OFF POSITION FREEZE Sound Button Press to select an AutoSoundTM control. Choose from three factory-set controls (VOICE, MUSIC, and THEATRE) and a PERSONAL control that you set according to your own preferences through the onscreen Sound menu. The three factoryset controls will tailor the TV sound so as to enhance the particular type of program you are watching. Picture Button Press to select an AutoPictureTM control. Choose from four factory-set controls (MOVIES, SPORTS, WEAK SIGNAL, and MULTI MEDIA) and a PERSONAL control that you set according to your own prefernces through the onscreen PICTURE menu. Press the CURSOR RIGHT button to shift the menu to the left. Press the CURSOR DOWN button until either TUNER MODE A or TUNER MODE B is highlighted. Press the CURSOR RIGHT button to highlight the tuner options. With the TUNER MODE control set to AUTO, Auto Program (see below) will detect whether or not cable input is present. If, however, you want to set the TUNER MODE to CABLE or ANTENNA, press the CURSOR UP or CURSOR DOWN button until either CABLE or ANTENNA is highlighted. Press the STATUS/EXIT button to clear the menu from the screen. PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT SLEE P 1 4 7 SOU ND TV/V SW AP CR ON/O FF POSI TIO UP PIP CH POW PIP N FRE EZE ER INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT 1 2 5 8 0 M-L INK SOU RCE DN 3 6 9 INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT 7 VOL SOU ITR /R RCE MU STAT U S/EX IT CC E HOM MO VIE S E PER SON CLO CK TE EC HOM VID EO MEN U PIC TUR INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT AUTO CABLE ANTENNA E CH 3 2 4 6 5 SMART HELP When CABLE is selected, channels 1125 are available. When ANTENNA is selected, channels 269 are available. INC R. PRO GRA M LI ST SUR AL R. OPEN /CLO SE SUR TUN ER A/B F AUTO PROGRAM Y our TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in your area by pressing the CHANNEL (+) or () button. Press the MENU button on the remote control to show the onscreen menu. Press the CURSOR DOWN button repeatedly until INSTALL is highlighted. Press the CURSOR RIGHT button to shift the menu to the left. LANGUAGE will be highlighted. Press the CURSOR DOWN button repeatedly until the AUTO PROGRAM control is highlighted. Press the CURSOR RIGHT button to start the Auto Program scanning of channels. Press the STATUS/EXIT button to clear the menu from the screen. PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT SEARCH SLEE P INSTALL LANGUAGE TUNER MODE A TUNER MODE B AUTO PROGRAM CHANNEL EDIT CABLE TUN-A PLEASE WAIT CHANNEL 12 1 4 7 SOU ND TV/V SW AP CR ON/O FF POSI UP PIP POW 1 2 5 8 0 PIC M-L INK SOU RCE TIO N PIP FRE EZE ER CH DN 3 6 9 TUR E SMART HELP After youve run Auto Program, check out the results. Press the CHANNEL (+) or () button and see which channels you can select. 3 6 VOL SOU ITR /RE RCE MU STAT U S/EX IT CC E HOM E MO VIE S PER SON AL CLO CK TE C HOM VID EO MEN U CH 3 2 4 5 INC R. [. . . ] LANGUAGE will be highlighted. Press the CURSOR DOWN button until the AutoChron control is highlighted. Press the CURSOR RIGHT button to start the AutoChronTM feature. Then just follow the onscreen instructions to set the clock. Press the CURSOR RIGHT button to select AUTO. [. . . ]