User manual PHILIPS 28PW6332

[. . . ] Introduction Thank you for purchasing this television set. Every effort has been made to simplify the operation and tuning of the receiver by the use of menus. These menus are displayed on screen when requested giving easy access to the various adjustments. This handbook has been designed to help you install and operate your TV set. [. . . ] This mode is used when a film or programme has been recorded or encoded in Dolby Surround sound. These films or programmes are always indicated by the symbol . Dolby 3 Stereo (with Stereo sources) Dolby 3 Stereo sound is produced only on the left (L), right (R) and centre (C) channels. Hall Surround (with mono or Stereo sources) The left (L) and right (R) channels are reproduced on the left and right loudspeakers of the TV set and on the rear channel (S), creating a "Hall Surround" ambient effect. This mode is recommended for broadcasts that are not encoded in Dolby Surround if you wish to use a rear channel. To exit from the menu : Press the blue key. Dolby Pro Logic and Dolby 3 Stereo modes are not recommended for mono transmissions (only the central channel is used). Hall Surround Sound level This menu is used to balance the volume between the loudspeakers. æ Select SOUND LEVEL (  Select TEST ( ê Use the keys) and press the The SOUND LEVEL menu appears. key. keys) and press the key. A continuous sound is emitted in turn from each channel: left, right, centre and rear channel. keys to adjust the level of each channel independently: BALANCE, CENTRE and REAR. The sequence stops while the level is being changed and then automatically starts up again. Levels may also be adjusted without using the test signal. * Manufactured under license from Dolby Laboratories Licensing Corporation. "Dolby" "Pro Logic" and the double-D symbol Laboratories Licensing Corporation. are trademarks of Dolby 13 Equalizer æ Select EQUALIZER (  Use the ê Use the keys) and press the The EQUALIZER menu appears. key. keys to select each frequency (from bass: 100 Hz to treble: 10 kHz) keys to adjust the level. : Press the blue key. To exit from the menu Spatial This setting increased the stereo effect giving the impression that the loudspeakers are spaced further apart. Headphones This setting allows the volume of the headphones to be adjusted independently from the TV set. To exit from the menu : Press the blue key. Features Child Lock The child lock function is an electronic lock which disables the keys on the TV set. æ Display the FEATURES menu (yellow  Select CHILD LOCK ( ê Use keys). keys to switch to ON. key). ® Switch off the TV set and remove the remote control. The television can no longer be used. The TV set can only be switched on using the remote control. To cancel: Return CHILD LOCK to OFF in the features menu. Storing adjustments This function allows you to store your own picture and sound adjustments. The adjustments are restored every time your set is switched on, or by pressing the green key on your remote control. General storing æ First carry out your PICTURE and SOUND adjustments and adjust the volume ( key) and then: key).  Display the FEATURES menu (yellow ê Select STORE PP ALL ( keys) and press . The message OK appears. All the PICTURE and SOUND menu adjustments as well as the volume are stored. 14 Storing adjustments for each programme This function allows you to correct any differences in levels which may exist between TV channels and/or EXT sockets. It allows you to store BRIGHTNESS, COLOUR, SHARPNESS, NOISE REDUCT, SOUND MODE and volume adjustments ( key). æ Carry out desired corrections to settings for the programme (or EXT connection), and then:  Display the FEATURES menu (yellow key). ê Select STORE PP P: _ _ ( keys) and press . The message OK appears. The adjustments are stored. Repeat for each programme that needs correcting. Programming Sleeptimer æ Select PROGRAMMING ( From the FEATURES menu (yellow key).  Select SLEEPTIMER and use to enter the length of time after which the TV will switch to standby mode (up to 180 mins). Press the key to display the length of time remaining. [. . . ] Check that the external loudspeakers switch has not been activated by mistake (p. 20). The Surround Sound loudspeakers do not work?For them to function correctly it is essential that both loudspeakers are connected: check connections. If in doubt, use the SOUND LEVEL menu (p. 13) to check each channel. Remote control The TV set does not react to the remote control; the orange indicator on the TV set no longer flashes when you use the remote control? [. . . ]