User manual PHILIPS 30HW9100D

[. . . ] L05 User's Manual 091105. 1833 26HW9100D/30HW9100D User's Manual 1 L05 User's Manual 091105. 1833 SAFETY INFORMATION · Disconnect mains plug when: Ø the red light below the TV screen is flashing continuously. Ø a bright white line is displayed across the screen. Use a slightly damp chamois leather or soft cloth. Ø the set is left unattended for a prolonged period of time. [. . . ] AUDIO MUTE: o Specify whether audio for the current channel is to be audible (AUDIO MUTE = NO) or muted (AUDIO MUTE = YES). CABLE (NO / YES) Select either standard off-air tuning (CABLE TUNING = NO) or cable offset tuning (CABLE TUNING = YES). FACTORY CH RESET Cursor Right will reset the channels programmed in memory. (>) 13 L05 User's Manual 091105. 1833 USE CHANNEL TABLE (NO/YES) When NO is selected the MAJOR channel in the Digital channel setup in the CHANNEL INSTALLATION menu refers to an RF channel (frequency). When YES is selected the Major channel refers to the Major channel listed in the Digital Channel Map. DIGITAL OSD (NO/YES) Specify whether the consumer digital version of the OSD is displayed when MENU is pressed from a digital channel. ENTER DIGITAL MENU Cursor RIGHT will bring up the Consumer DIGITAL Menu below: (>) The primary use of this menu is to program the digital channels using the Auto Program function of the digital module in the television. To program the digital channels, cursor down to Install, and Cursor Right. From The Install menu, select Auto Program and Cursor Right to start the Auto Programming. 14 L05 User's Manual 091105. 1833 Note: The digital channels must be programmed using the Digital Menu to allow for the fastest possible channel change times. To exit the digital menu, press the key on the setup remote twice. (||||||||||||| 0 ­ 100) BRIGHTNESS Adjust the respective picture setting, using left and right cursor. COLOR Adjust the respective picture setting, using left and right cursor. CONTRAST Adjust the respective picture setting, using left and right cursor. SHARPNESS Adjust the respective picture setting, using left and right cursor. TINT Adjust the respective picture setting, using left and right cursor. ROTATION Adjust the respective picture setting, using left and right cursor. DEFAULT FORMAT (||||||||||||| 0 ­ 100) (||||||||||||| 0 ­ 100) (||||||||||||| 0 ­ 100) (||||||||||||| -31 - 31) (||||||||||||| 0 ­ 100) (WIDESCREEN / 4:3 / ZOOM 14:9 / ZOOM 16:9 / SUBTITLE ZOOM / SUPER ZOOM) Set the default screen format of the television at Power On. The pictures you receive may be transmitted in 16:9 format (wide screen) or 4:3 format (conventional screen). 16:9 pictures sometimes have a black band at the top and bottom of the screen (letterbox format). This function allows you to optimize the picture display on screen. 15 L05 User's Manual 091105. 1833 Using the different formats Select the preferred format from the DEFAULT FORMAT menu item in the setup screen, or (if applicable) use the Format button on the Remote Control to select the different modes: 4:3, Zoom 14:9, Zoom 16:9, Subtitle zoom, Super Zoom, and Widescreen. 4:3 The picture is reproduced in 4:3 format and a black band is displayed on either side of the picture. Zoom 14:9 The picture is enlarged to 14:9 format, a thin black band remains on both sides of the picture. Zoom 16:9 The picture is enlarged to 16:9 format. This mode is recommended when displaying pictures that have black bands at the top and bottom (letterbox format). Subtitle Zoom This mode is used to display 4:3 pictures using the full surface of the screen leaving the subtitles visible. Super Zoom This mode is used to display 4:3 pictures using the full surface of the screen by enlarging the sides of the picture Widescreen This mode restores the correct proportions of pictures transmitted in 16:9 using the full screen display. NOISE REDUCTION (NO / YES) Disable or enable the video noise reduction feature, in which video noise is reduced, with minimum reduction in picture sharpness. 16 L05 User's Manual 091105. 1833 SOUND MODE (MONO / STEREO) Select either STEREO or MONO (monaural) sound modes. Note: STEREO has no effect if the current audio signal is monaural. When SOUND MODE is changed, an on-screen display will appear, indicating the actual audio status (MONO or STEREO) AVL (OFF / ON) Disable or enable the Automatic Volume Leveling feature, which minimizes variations in audio playback level. [. . . ] YES: When the television is powered down and back on again, the closed captioning setting last specified in CC (see CC) will remain in effect. SOURCE MENU ITEM (NO / YES) This feature provides the option to specify whether the current signal source (e. g. , TV 54, AUX, CVI, S-VIDEO, etc. ) item is present in the FEATURES MENU that appears when the remote control SLEEP or CC command is issued, or when a guest- mode remote control RECALL command is issued. Features Menu With SOURCE MENU ITEM = YES NO: The SOURCE line item is does not appear in the FEATURES MENU. YES: The SOURCE line item appears in the FEATURES MENU. Note 1: When the SOURCE item is highlighted, cursor right or left to step through the signal sources (e. g. , tuner, AUX, S-VIDEO, etc. ) that are in the CHANNEL RING. [. . . ]