User manual PHILIPS 32-SCAN3 W-NET1 SC3132N

[. . . ] Most importantly, you can count on our uncompromising commitment to your total satisfaction. All of this is our way of saying welcome - and thanks for investing in a PHILIPS product. P T get the most from your PHILIPS purchase, be sure to complete and . S. o return your Product Registration Card at once. [. . . ] The Contrast + control helps to "sharpen" the picture quality. The black portions of the picture become richer in darkness and the whites become brighter. Picture Brightness Color Picture Sharpness Tint Color Temp. 50 Brightness Color Picture Sharpness Tint Color Temp. 65 50 50 50 0 Normal Warm or Cool On Off On Off DNR Contrast + 16 SOUND MENU CONTROLS o your and TuseadjustSound TV sound, selectlisted the Menu Controls below: 1 2 3 4 5 6 7 Treble: Press the CURSOR RIGHT 2 or LEFT 1 buttons to adjust the control. The control will enhance the high frequency sounds. Bass: Press the CURSOR RIGHT 2 or LEFT 1 buttons to adjust the control. The control will enhance the low frequency sounds. Balance: Press the CURSOR RIGHT 2 or LEFT 1 buttons to adjust the level of sound coming from the left and right speakers. AVL: (Auto Volume Leveler) Press the CURSOR RIGHT 2 or LEFT 1 buttons to turn the control On or Off. When On, AVL will level out the sound being heard when sudden changes in volume occur during commercial breaks or channel changes. Surround: Press the CURSOR RIGHT 2 or LEFT 1 buttons to select between Dolby Virtual or Stereo settings (If Stereo), or select Spatial or Mono (If Mono). SAP: Press the CURSOR RIGHT 2 or LEFT 1 buttons to toggle this control to On or Off. SAP is short for Secondary Audio Programming and is sent as a third audio channel, a SAP signal can be heard apart from the current TV program sound. Note: If SAP is not present on a selected show No SAP will appear on the screen. Press the CURSOR RIGHT 2 button to display the Timer menu. Press the CURSOR UP 3 or DOWN 4 buttons to scroll through the Timer menu until Start Time or Stop Time is highlighted. Enter the correct time by using the Numbered buttons. Press the CURSOR RIGHT 2 or CURSOR LEFT 1 buttons to change the AM or PM setting. When finished, press the STATUS /EXIT button to remove the on-screen menu from the TV's screen. 1 7 2 5 6 2 58 VOL Timer Time Start Time Stop Time Channel Activate Display Timer Time Start Time Stop Time Channel Activate Display --:-- AM 3 4 7 10:-- AM Timer Time Start Time 10:35 AM Stop Time Channel Activate Display Timer Time Start Time Stop Time 10:35 AM Channel Activate Display Timer Time Start Time 10:35 PM Stop Time Channel Activate Display Timer Time Start Time Stop Time 10:35 PM Channel Activate Display NOTE: The Activate Control must be set to Once or Daily for the television to turn On or Off at the specified time. See panel 21 for more details. HELPFUL HINTS Remember, be sure to press "0" and then the hour number for single digit entries. You can get to the Clock setting by pressing the Clock button on the remote control. The TV's clock settings may be lost when the TV is unplugged or when AC power to the set is interrupted. NOTE: Active Control will only appear in the menu of models 27PT6441/37 and 27PT6442/37. 20 SETTING TV TO STARTUP ON A SPECIFIC CHANNEL can select a specific You the timer turns the setchannel that the television will tune to when On. Follow these steps to select the channel. Main Picture Sound Features Install 1 2 3 4 5 6 7 Press the MENU button on the remote to show the onscreen menu. Press the CURSOR UP 3 or DOWN 4 buttons to scroll through the on-screen menu until the word Features is highlighted. Press the CURSOR RIGHT 2 button to display the Features menu. [. . . ] · Check the MUTE button on the remote control. · If you're attempting to hook up auxiliary equipment, check the audio jack connections located on the front of the TV. Remote Does Not Work · Check the batteries. If necessary, replace them with AA Heavy Duty (Zinc Chloride) or Alkaline batteries. [. . . ]