User manual PHILIPS 34618-48-16

[. . . ] The remote control can be set up to operate any 3 of the following devices: Device name TV DVD Traditional TV, LCD / Plasma TV and projection TV, TV part of TV / DVD combos DVD player / recorder (DVDR), DVD / Hard Disk Drive combination (DVDR-HDD), Blu-Ray player, High Definition DVD player (HD-DVD), DVD part of TV / DVD combos Description 2 EN CBL/SAT Cable box, satellite receiver, Internet Protocol TV (IPTV), Free To Air TV, High Definition Television decoder (HDTV) and TiVo 5 Switch ON the TV. Example: setting up the universal remote control to operate your TV: 1 Switch ON the TV manually or use the original remote control for this. deviceselection button for 5 seconds until the red Setup light blinks. · The remote control is now in setup mode. 3 Look up the 4-digit code for your brand in the brand list at the back of this user manual. [. . . ] when you try to repair the Play button for your DVD player, make sure to insert a DVD into the DVD player otherwise the Play button is not able to function. 2 Press the button that does not function, keep it pressed and immediately release it when the device responds. Repeat this for every button that does not function. · If the button still does not function as expected, try pressing it again for a longer period of time. 5 3 3. 1 Using the universal remote control Buttons and functions 1 Make sure the receiving device is able to After initial setup 2 respond. when you try to repair the Play button for your DVD player, make sure to insert a DVD into the DVD player otherwise the Play button is not able to function. Select the device that you wish to operate (e. g. Press the device selection button to select DVD. The illustration on page 8 gives an overview of all buttons on the remote control. Try out the buttons you need for operating your devices. Notes · Buttons having the same functions as the buttons on your original remote control may have different namings on the 34618-48-16 (e. g. Only functions that are available on your original remote control can be used for operating your devices with the 34618-48-16. · 6 EN EN 7 Using the universal remote control 2. 2. 2 Improving buttons When correctly set up, the remote control should be able to operate all your devices. However, when using the remote control for the first time it might occur that some buttons do not yet function as expected. 2x · After each button press the red Setup light blinks once. · The red Setup light will blink one more time to confirm that the button was succesfully reset to its original function. 5 sec. 10 EN EN 11 Using the universal remote control English Resetting a button to its original function 4 4. 1 Service and support Frequently asked questions 4. 1. 1 Setup I cannot enter setup mode. Battery level too low or battery lifetime came to an end. After replacing the batteries, test if the remote control still operates your devices. If it does not, you have to set up the remote control again. The brand code for my device is missing in the `Shortlist of brands' in the Quick Start Guide. The `Shortlist of brands' only mentions the most common TV, DVD and CBL/SAT brands. · You will find a complete brand list on page 18-31 of this user manual. · Use `9999' as 4-digit code in case you cannot find your brand in the complete brand list. Note that using `9999' may result in a long setup (up to 15 minutes). 4. 1. 2 Operation The remote control does not wake up anymore. Battery level too low or battery lifetime came to an end. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. [. . . ]