User manual PHILIPS 40714-31-16

[. . . ] Please refer to safety and disposal instructions for batteries in this user manual. The `exclamation mark' calls attention to features for which you should carefully read the supplied literature to prevent operating and maintenance problems. The `lightening bolt' symbol indicates uninsulated components within the product that can cause an electric shock. 7R UHGXFH WKH ULVN RI ÀUH RU HOHFWULF VKRFN GR not expose the product to rain or moisture and GR QRW SODFH DQ\ REMHFWV ÀOOHG ZLWK OLTXLGV VXFK as vases, on the product. g Do not block any ventilation openings. [. . . ] Make sure that your iPod touch/iPhone/ iPad or PC/Mac are also connected to the same Wi-Fi network. 10 EN 3 Prepare Always follow the instructions in this chapter in sequence. Tip After AC power connection, if the built-in battery is full, the power indicator on the front of the unit stays blue; if the built-in battery is not full, the power indicator ÁDVKHV EOXH LI WKH EDWWHU\ LV ÁDW WKH SRZHU LQGLFDWRU turns red. English Connect power Turn 40714-31-16 on Caution Risk of product damage!Make sure that the power supply voltage matches the voltage printed on the bottom of the unit. When you unplug the AC adaptor, always pull the plug from the socket. Before you connect the AC adaptor, make sure that you have completed all the other connections. 1 2 Press on the top to turn the unit on. Wait for successful boot-up of the unit. » The boot-up takes about 35 seconds. » During boot-up, the Wi-Fi SETUP indicator on the back of the unit blinks green quickly. » After boot-up, if no Wi-Fi connection has been set up for 40714-31-16, the Wi-Fi SETUP indicator starts to blink green slowly. 40714-31-16 is designed with a built-in battery that allows you to enjoy music on the go. Before use, make sure to fully charge the built-in battery. To turn the unit off, press again. 1 2 Dock the 40714-31-16 main unit on the charging stand. Connect the AC power cord to the DC IN socket on the back of the charging stand. the wall power socket. EN 11 4 Connect to your home WiFi network for AirPlay Before connection of 40714-31-16 to you home Wi-Fi network, check the points below. 1 2 3 Make sure that your Wi-Fi router is powered on and working properly. Make sure that 40714-31-16 has been powered on and booted up successfully (see `Turn 40714-31-16 on' on page 11). Please power off both your Wi-Fi router and 40714-31-16 and then power on them again to see whether 40714-31-16 can be connected to your home Wi-Fi network. If the problem remains, try the above procedures again. $IWHU \RX ÀQLVK WKH DERYH FKDQJHV RU SRZHURII DQG power-on of 40714-31-16, the new Wi-Fi network created by 40714-31-16 will disappear. Tip If you like, you can change the name of your 40714-31-16 in Advanced settings -> AirPlay Device Name on the '6: FRQÀJXUDWLRQ ZHE SDJH 7KLV LV KHOSIXO ZKHQ you have multiple Philips AirPlay-enabled devices in your house and you need to distinguish between them. If you want to enter the network name (SSID) manually (for example, if you want to hide your SSID), go to Advanced settings -> CONFIGURE MANUALLY on WKH '6: FRQÀJXUDWLRQ ZHE SDJH Restore your Wi-Fi enabled device back to your existing home Wi-Fi setting Note Make sure that the settings at steps 2 to 3 below match your home Wi-Fi network settings you wrote on paper. 2 Select your network name (SSID) from the list of available wireless networks. 1 Select Settings -> Wi-Fi on your iPod touch/iPhone/iPad. Or open the list of available Wi-Fi networks on your PC/Mac. 3 4 18 EN Enter the network key if required. Wait until successful Wi-Fi connection to your home Wi-Fi network. 5 Play Stream audio from your iTunes music library to 40714-31-16 Note Make sure that your iTunes host device is connected to the same Wi-Fi network as 40714-31-16. Your iTunes device can be an iPod touch/iPhone/iPad installed with iOS 4. 3 (or later) or a Wi-Fi enabled PC/Mac installed with iTunes 10 (or later). 3 Stream from your iPod touch/iPhone/ iPad 4 1 2 Launch the iPod application on your iPod touch/iPhone/iPad. Tap on the AirPlay icon. 6HOHFW D PHGLD ÀOH DQG VWDUW SOD\ » After a while, you will hear music from 40714-31-16. Note If you fail to hear music after successful setup, do one of the following on your iPod touch/iPhone/iPad: (1) Disconnect and then re-connect to the same Wi-Fi router again; (2) Close all applications running at the background; (3) Power off and then power on your iPod touch/ iPhone/iPad again. EN 19 English Select Philips_Fidelio XXXX (or user FXVWRPL]HG QDPH IURP WKH $LU3OD\ OLVW Stream from your PC/Mac Tip When you stream audio from your iTunes music library on a PC/Mac, you can select more than one AirPlayenabled devices (if available) at step 3 to stream music to all of them at the same time. If you are using an earlier version of iTunes, the AirPlay icon may be instead of . 1 2 Launch iTunes 10 (or a later version) on your PC/Mac. Click the AirPlay icon on the window. Control play You can select different play options from either your iTunes host device or 40714-31-16. Note 3 Select Philips_Fidelio_AirPlay XXXX (or XVHU FXVWRPL]HG QDPH IURP WKH $LU3OD\ OLVW Make sure that you have successfully streamed audio from your iTunes music library to 40714-31-16. To pause or resume play, press . To adjust volume, press +/- repeatedly. Tip If you are streaming music from a PC/Mac, to control music play from 40714-31-16, remember to tick Allow iTunes audio control from remote speakers in Edit -> Preferences -> Devices on iTunes. 4 6HOHFW D PHGLD ÀOH DQG VWDUW SOD\ » After a while, you will hear music from 40714-31-16. Use advanced sound settings If your iTunes host device is an iPod touch/ iPhone/iPad: For advanced sound settings and additional features, you can use your iPod touch/iPhone/ iPad to download the Philips Fidelio application from Apple App Store. [. . . ] No response from the unit Press and hold both the + and - buttons on 40714-31-16 for more than 5 seconds to reset the device. Then set up the Wi-Fi network for 40714-31-16 again. Disconnect and reconnect the AC power plug, and then switch on the device again. Wi-Fi network connection failed Check if your Wi-Fi router is Wi-Fi EJ FHUWLÀHG 7KLV GHYLFH LV RQO\ FRPSDWLEOH ZLWK :L)L EJ FHUWLÀHG routers. If your Wi-Fi router is Wi-Fi 802. 11n FHUWLÀHG PDNH VXUH WR HQDEOH WKH 802. 11b/g mode. [. . . ]