User manual PHILIPS 42FD9932-01G

[. . . ] Note: This connector can also be used for dealer service tools. é Directly to the monitor & Connect one end of a VGA cable 1 to the video card of the computer and the other end to the VGA 1 connector at the rear side of the monitor. Fix the connectors firmly with the screws on the plug. In case of a Multimedia computer, connect the audio cable 2 to the audio outputs of your Multimedia computer and to the AUDIO VGA 1 R (right) and L (left) inputs of the monitor. L L VGA 1 VGA 2 RC OUT R R VGA 2 ~ MAINS RS232 VGA 1 AUDIO IN é 2 1 1 English Monitor Display modes VGA Wide VGA Wide VGA MAC MAC MAC MAC SVGA XGA SXGA 640x480 848x480 852x480 640x480 832x624 1024x768 1152x870 800x600 1024x768 1280x1024 60, 72, 75, 85 Hz 60 Hz 60 Hz 66. 67 Hz 74. 55 Hz 74. 93 Hz 75 Hz 56, 60, 72, 75, 85 Hz 60, 70, 75, 85 Hz 60, 72 Hz When a VGA computer is connected, the display selection is made automatically. A message is displayed when the monitor does not support the connected VGA mode. [. . . ] Nevertheless in many countries batteries may not be disposed of with your household waste. Please ensure you dispose of batteries according to local regulations. End of life directives Philips is paying a lot of attention to produce environmentally-friendly in green focal areas. Your new monitor contains materials which can be recycled and reused. At the end of its life specialised companies can dismantle the discarded monitor to concentrate the reusable materials and to minimise the amount of materials to be disposed of. Please ensure you dispose of your old monitor according to local regulations. 3 Use of the menus and the menu system Picture 1 Picture 2 Contrast Colour temp. Sharpness Sound Setup Brightness Contrast This control allows you to adjust the contrast level of the picture. Colour temperature This control allows you to select the colour temperature of the picture. Move the cursor up/down to make a selection. Press the cursor left to return to the Picture 1 menu. Sharpness This control allows you to adjust the edge definition of a picture. & Press the MENU key on the remote control to summon the different menu headers. é Press the cursor left/right to move the cursor horizontally through the menu headers. " Press the cursor down to access the menu. In case of a slider, move the cursor left/right to adjust. In case of a list with options, move the cursor right to enter and use the cursor up/down to select an option. Do not use abrasives solvents as it can damage the glass surface of the screen. Plasma Display characteristics Caution: A video source (such as a video game, DVD, or video information channel) which shows a constant non-moving pattern on the screen, can cause damage to the screen. When your Flat-Monitor is continuously used with such a source, the pattern of the non-moving portion of the game (DVD, etc. ) could leave an image permanently on the screen. When not in use, turn the video source OFF. Regularly alternate the use of such video sources with normal viewing. When switching over to another picture after having displayed the same still picture for a long time (many hours), it may happen that some parts from the previous picture will remain on screen due to a kind of memory effect. This ghost picture will disappear after some time. To avoid this effect change the pictures regularly or for PC use you can turn on a screen saver in your computer. For video signals, Philips has built in an automatic shift of the picture every 5 minutes to avoid this effect and to prolong the life of the screen. Very incidentally and after a longer period of unuse (approx. 1 year) the screen may display some strange colour deficiencies. This is quite normal for plasma displays and these effects will 6 disappear after the set has been turned on for some time. A plasma display consists of a huge amount of colour pixels. It is within industry standards that very few pixels (< 0. 001%) may be defective, even for a new set. [. . . ] (The power cable to the display, the VGA cables, the audio cables, . . . ) Is your PC or receiver box switched on?Do you see a black screen and the indicator on front of the monitor lights up green, this means that the display mode is not supported. Switch your VGA source to a correct mode. If your problem is not solved: Switch your monitor off and then on again. [. . . ]