User manual PHILIPS 42FD9932-69G

[. . . ] Consult your dealer. To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be placed on or in the vicinity. Avoid heat, direct sunlight and exposure to rain or water. The equipment shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on it. min. 1m Connect your computer & é L L R RS232 ~ MAINS DVI-D VGA 2 AUDIO Directly to the monitor Connect one end of a VGA cable 1 to the video card of the computer and the other end to the VGA 1 connector at the rear side of the monitor. [. . . ] (Tint) Sharpness Picture 1 menu Brightness This control allows you to adjust the brightness level of the picture. G H C @ è à Contrast This control allows you to adjust the contrast level of the picture. Color (only available when the source is AV1, AV2 or AV3 YCbCr) This control allows you to adjust the saturation level of the colors to suit your personal preference. Color temperature This control allows you to select the color temperature of the picture. Move the cursor up/down to make a selection. Press the cursor left to return to the Picture 1 menu. Tint (only with NTSC signals and when the source is AV1 or AV2) This control allows you to compensate for the color variations in NTSC encoded transmissions. Sharpness This control allows you to adjust the edge definition of a picture. VGA-mode + HD video mode Picture 1 Brightness Contrast Color temp. Sharpness G H @ à 4 Use of the menus 1015. 5 en 12-11-2003 11:12 Pagina 5 SD video-mode Picture 2 Format q 4:3 Movie expand 16:9 Wide screen Zoom Z Zoom factor  Picture 2 menu Zoom Select Zoom On to activate the zoom function. You may also activate the zoom function with the ZOOM ON/OFF button on the remote control. If no zoom is active, press the cursor left/right, up/down to select which part of the screen will be zoomed. Zoom factor Select Zoom factor and press the cursor left/right to adjust the zoom factor and to change the magnification of the picture. In case Power savings is switched Off, the power always remains on until the monitor is forced to standby. & é Use the cursor down to select Power savings. Press the cursor left/right to select On or Off. AV3 This control allows you to set the AV3 input to HD-RGB, YCbCr or HDYPbPr. When having selected Auto, the monitor makes the selection automatically between YCbCr, HD-YPbPr or HD-RGB. 7, Equipment with Component Video Output connectors. & é " Use the cursor down to select AV3. Press the cursor right to enter the list with options. Press the cursor up/down to select one of the options. VGA2 This control allows you to select whether to set the VGA2 connector as input, output or even HD-input. & é " Use the cursor down to select VGA2. Press the cursor right to enter the list with options: VGA IN, VGA OUT or HD IN. Press the cursor up/down to select one of the options. Note: AV3 and VGA2 will not be available in VGA loop through mode, i. e. when a receiver box is connected to the monitor and a VGA source is selected. 6 Use of the menus 1015. 5 en 12-11-2003 11:12 Pagina 7 Connect Peripheral Equipment You may connect 3 possible VGA sources (VGA1, VGA2 or DVI-D) and 3 possible video sources (AV1, AV2 and AV3) to the monitor. The following diagrams show you where you can connect your peripheral equipment. [. . . ] The plasma display technology operates with rare gases which are being influenced by air pressure. Up to an altitude of 6562 ft (local air pressure equal or above 800 hPa) above sea-level, the display is functioning fine. Operating the set at a higher altitude (lower air pressure), the picture becomes unstable and the picture performance is deteriorating. The plasma display might then also produce a humming sound. After bringing the set below 6562 ft (local air pressure equal or above 800 hPa) it works fine again. Transportation has no influence. [. . . ]