User manual PHILIPS 42PFL3007T

[. . . ] The material in this manual is believed adequate for the intended use of the system. If the product, or its individual modules or procedures, are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained. Philips warrants that the material itself does not infringe any United States patents. No further warranty is expressed or implied. [. . . ] Press OK. Note · To disable the clock, repeat the procedure. EN 21 Change the clock mode 1 2 Use timers You can set timers to switch the TV to standby at a specified time. Tip · Set the TV clock before you use timers. Press . 3 Select [Setup] > [TV settings] > [Preferences] > [Clock] > [Auto clock]. Select [Automatic] or [Manual], then press OK. Change the time zone Note · This option is only available if you select [Auto clock] > [Automatic] (in countries with clock transmission data). Automatically switch the TV to standby (sleep timer) Sleep timer switches the TV to standby after a pre-defined duration. Tip · You can switch off your TV earlier or reset the sleep timer during the countdown. 1 2 3 4 Press . Select [Setup] > [TV settings] > [Preferences] > [Clock] > [Time zone]. Press OK to confirm. 1 2 3 4 Press . Use daylight saving Note · This option is only available if you select [Auto clock mode] > [Manual]. Select [Setup] > [TV settings] > [Preferences] > [Sleep timer]. Select a value between zero and 180 minutes. » If you select zero, the sleep timer switches off. » The TV switches to standby after the specified time. 1 2 3 Press . Select [Setup] > [TV settings] > [Preferences] > [Clock] > [Daylight saving], then press OK. Select [Standard time] or [Daylight saving time], then press OK. 22 EN Lock unsuitable content You can prevent your children from watching certain programmes or channels by locking the TV controls. Lock or unlock one or more channels English 1 2 Press > [Setup] > [Channel settings] > [Child lock] > [Channel lock]. » A list of channels is displayed. Select the channel that you want to lock or unlock, then press OK. » The first time you lock or unlock a channel, you are prompted to enter your PIN code. » If the channel is locked, a lock icon is displayed. Select a picture, then press Select [Set as Scenea], then press OK. Press any button to exit Scenea. Show or hide subtitles 1 2 While you watch TV, press SUBTITLE. Select one of the following, then press OK. · [Subtitles on]: Always display subtitles. · [Subtitles off]: Never display subtitles. · [On during mute]: When audio is muted, display subtitles. Note · Repeat this procedure to enable subtitles on each · Select [Subtitles] > [Subtitles off] to disable subtitles. 24 EN analogue channel. Note · When you select a subtitle language in a digital TV channel as described below, the preferred subtitle language set in the installation menu is temporarily overruled. · 1 2 3 4 While you watch TV, press Select a subtitle language. · Select [Subtitle language], then press OK. Press the following buttons to control play: · to play. · or to play the previous or next photo. To return, press . Change slide show settings Play photos, music and videos on USB storage devices Caution · Philips is not responsible if the USB storage device is not supported, nor is it responsible for damage or loss of data from the device. 1 2 While you view a slide show, press OPTIONS. » The slide show options menu is displayed. Select one of the following, then press OK. [. . . ] Check the signal output of the device. HDMI connection issues There are problems with HDMI devices: · Note that HDCP (High-bandwidth Digital Content Protection) support can delay the time taken for a TV to display content from a HDMI device. · If the TV does not recognise the HDMI device and no picture is displayed, try switching the source from one device to another and back again. · If there are intermittent sound disruptions, check that output settings from the HDMI device are correct. · If you use an HDMI-to-DVI adapter or HDMI-to-DVI cable, check that an additional audio cable is connected to AUDIO IN (mini-jack only). English Sound issues There is a picture but sound quality is poor: Note · If no audio signal is detected, the TV automatically switches the audio output off -- this does not indicate malfunction. Computer connection issues The computer display on the TV is not stable: · Check that your PC uses the supported resolution and refresh rate. [. . . ]