User manual PHILIPS 43266-56-16

[. . . ] This product shall not be exposed to dripping or splashing. The mains plug of AC/DC adaptor is used as the disconnect device, the disconnect device shall be readily operable. Be sure to observe the following guidelines when using your headphones. • • Listen at reasonable volumes for reasonable periods of time. Be careful not to adjust the volume continuously upwards as your hearing adapts. [. . . ] Be careful not to adjust the volume continuously upwards as your hearing adapts. Do not turn up the volume so high that you can’t hear what’s around you. You should use caution or temporarily discontinue use in potentially hazardous situations. Excessive sound pressure from earphones and headphones can cause hearing loss. • • • • • • • • Electric-, Magnetic- and Electromagnetic Fields (EMF) 1. Royal Philips Electronics manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals. One of Philips’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within 2 EN • • • • Only use rechargeable NiMH batteries (capacity over 700mAh) with your headphones. Other types of rechargeable or alkaline batteries cannot be charged with this system. AAA alkaline batteries can be used to operate the headphones. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. • • • Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet. ) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. »» The LED on the transmitter turns on. Tip •• You can also adjust the volume on the audio device. 1 2 3 4 • Install/Replace the supplied batteries (Fig. B). Power off the headphones and charge the headphones (Fig. D). Press INPUT to select ANALOGUE or DIGITAL mode (Fig. E). In ANALOGUE mode, connect the audio device to LINE IN sockets, then adjust ATT (Attenuation of audio input signal) (Fig. F). • For portable CD player, MP3 player or other devices with 3. 5mm triport socket output, connect with RCA to RCA cable (provided) and RCA to 3. 5mm plug adaptor (not provided), then switch ATT to 0dB. • For Hi-Fi, TV, DVD player or other devices with RCA socket output, connect with RCA to RCA cable (provided), then switch ATT to -8dB. • In DIGITAL mode, connect the digital audio device to DIGITAL IN COAXIAL socket with coaxial cable (not provided) (Fig. G). EN 5 L L 2 sec www. philips. com/w elcome Quick start guide 6 EN 4 LED indications Situation LED Searching Connection established Standby Low battery Charging Fully charged Non NiMH batteries 3D sound activated 3D sound deactivated Transmitter Analogue/Digital White Fast blinking Blinking Off --Off --------Headphones Charging Red ----Off --Blinking On Off ----3D sound White --------------On Off Red Fast blinking Blinking --Fast blinking ----------- EN 7 5 Sound indications Situation Low battery Turn the volume to maximum/minimum level Sound signal One “Beep” per 10 seconds Alert tone “Beep” 8 EN 6 Product information Transmitter System Modulation Carrier frequency Channels Radiated output power Effective transmission range Input Level Power requirements Headphones Playback frequency range Signal/Noise ratio Distortion Channel Separation Impedance Power Requirements Operating time 17 - 24, 000 Hz 89 dB Nominal < 0. 5% THD (Total Harmonic Distortion) 60 dB 32 ohm 2 x 700 mAh rechargeable NiMH batteries (supplied) or commercially available (AAA) dry batteries ~ up to 20 hours (actual result may vary) Radio Frequency (RF) MSK digital 2, 400 - 2, 483. 5 MHz 15 (auto-switching) 10 mW Approx. 100 meters (depending on ambient conditions) 800 mV (0 dB); 2 V (-8 dB) DC 5 V; 300 mA (from the supplied AC power adaptor) EN 9 7 Adaptor specification Region Europe (except U. K. ) U. K. /H. K. Adaptor type Input voltage number YLS0051A-E050030 100-240V~ S003IV0500030 100-240V~ YLS0051A-U050030 100-240V~ S003IB0500030 100-240V~ Output voltage 5V 5V 5V 5V , 300mA , 300mA , 300mA , 300mA Input frequency 50/60Hz 50/60Hz 50/60Hz 50/60Hz 10 EN 8 Frequently asked questions (FAQ) 1. Possible cause No battery installed or wrongly installed. Headphones wrongly placed into the charging dock. [. . . ] Adaptor type Input voltage number YLS0051A-E050030 100-240V~ S003IV0500030 100-240V~ YLS0051A-U050030 100-240V~ S003IB0500030 100-240V~ Output voltage 5V 5V 5V 5V , 300mA , 300mA , 300mA , 300mA Input frequency 50/60Hz 50/60Hz 50/60Hz 50/60Hz 10 EN 8 Frequently asked questions (FAQ) 1. Possible cause No battery installed or wrongly installed. Headphones wrongly placed into the charging dock. Solution Install or replace batteries properly (Fig. B). [. . . ]