User manual PHILIPS 50PF9965

[. . . ] Flat TV CVBS 1 CVBS 2 Y/C Y Cb/Pb DVD/HD1 Cr/Pr VGA 2 R/Cr/Pr G/Y B/Cb/Pb RGB/DVD/HD2 MAINS INLET HD VD DVI 3 EXTERNAL CONTROL CVBS B/Pb/Cb H VGA 1 VGA 2 RC-OUT VIDEO 1 (AV1) MAINS INLET L R L R AUDIO IN L Y CVBS AV1 Y/C S-VHS CVBS AV3 AUDIO AV4 AV2 RS232 ~ MAINS DVI-D Y/C S-VHS VIDEO 2 (AV2) G/Y/Y R/Pr/Cr VIDEO 3 (AV3) V VGA IN R AUDIO IN AUDIO OUT VGA OUT Cb Cr CVBS B/Pb/Cb H L L L VGA 1 R RS232 ~ MAINS DVI-D VGA 2 AUDIO VGA 2 RC-OUT 3 R R G/Y/Y R/Pr/Cr AV3 V AUDIO IN VGA 1 DVI-D AUDIO IN AUDIO IN Y/C S-VHS AV2 AV1 3 2 2 2 CABLE 1 EXTERNAL 5 ANTENNA EXTERNAL 3 EXTERNAL 4 Y AUDIO Pb L AUDIO OUT R L CENTER IN NO FUNCTION ~ MAINS EXTERNAL 1 EXTERNAL 2 Pr R PL/MAC IN L L MONITOR OUT AUDIO AUDIO R R 4 Contents Installation Help?If this instruction manual does not give an answer or if `Tips' do not solve your TV problem, you can call your Local Philips Customer or Service Centre. See the supplied World-wide guarantee booklet. Please, have the Model and Product number which you can find at the back of your television set or on the packaging, ready, before calling the Philips helpline. [. . . ] Connect your equipment with a eurocable 4 or 5 to one of the euroconnectors EXT1, 2, 3 or 4 to obtain a better picture quality. é Look for the test signal of your peripheral in the same way as you do for a recorder. " Make a selection in the Setup, Source menu, p. 9. VCR 1 DVD player EXTERNAL 5 Y U L 12 V R OUT With Component Video Output Connectors (EXTERNAL 5) & Connect the three separate component video cables to the DVD player's Y, U (Pb) and V (Pr) jacks and to the Y, Pb and Pr jacks on the receiver. é Connect the audio cable to the DVD player's AUDIO L and R jacks and to the L and R AUDIO EXTERNAL 5 jacks on the receiver. DVD 19 Side connections Camera or Camcorder & Connect your camera or camcorder as shown. é Connect to VIDEO 2 and AUDIO L 1 for mono equipment. For stereo equipment also connect AUDIO R 1. L A U D IO VI D EO IN S· VH S R S-VHS quality with an S-VHS camcorder is obtained by connecting the S-VHS cables with the S-video input 3 and audio inputs 1. Do not connect cable 2 and 3 at the same time. Headphone & Insert the plug into the headphone socket L as shown. é Press ¬ on the remote control to switch off the internal 1 2 3 loudspeakers of the TV. The headphone impedance must be between 8 and 4000 Ohm. In the Sound menu select Headphone volume to adjust the headphone volume. Multi channel Surround receiver & Connect the audio cable to the multi channel Surround receiver and to AUDIO OUT L and R at the back of your TV receiver CENTRE AUDIO OUT L R 2 1 box 1. é If you want the loudspeakers of your monitor to act as centre speaker, also connect an audiocable to the multi channel Surround receiver and to the SURROUND SOUND CENTRE IN at the back of your TV receiver box 2. " Select Centre Input On in the Source menu. The loudspeakers of the monitor will now only produce centre sound, the loudspeakers connected to the audio receiver will produce Surround Sound. The volume has to be controlled via the multi channel Surround receiver. Note: No sound will be heard when a TV channel or external source is blocked via the Child lock menu (see p. 13). Cinema Link surround receiver See the separate supplied Cinema Link instruction manual. Attention: the sound info on screen will not correspond with the actual sound reproduction. Connect your computer See the separate supplied instruction manual with your monitor. To select connected equipment Press the v key on the remote control repeatedly to select EXT1, EXT2, EXT3, EXT4, EXT5, FRONT or VGA according to where you connected your equipment at the back or the front side of your receiver. Remark : Most equipment (decoder, recorder) carries out the switching itself, when it is switched on. 20 VGA menu Only available when a VGA source has been connected and activated. See also the separate supplied instruction manual with your monitor. & Select VGA with the v key and press the OK key to confirm. é Press the MENU key to switch on the VGA menu. Picture 1 VGA " Select one of the menus with the cursor left/right. [. . . ] Operating the set at a higher altitude (lower air pressure), the picture becomes unstable and the picture performance is deteriorating. The plasma display might then also produce a humming sound. After bringing the set below 2000 m (local air pressure equal or above 800 hPa) it works fine again. Transportation has no influence. Control of peripheral equipment The infrared radiation of the screen may influence the reception sensitivity of other peripherals. Solution: replace the batteries of the remote control or change position of other equipment. [. . . ]