User manual PHILIPS AJ3136

[. . . ] When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Battery usage CAUTION ­ To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: G Install all batteries correctly, + and - as marked on the unit. [. . . ] Box 520890, Miami, FL 33152, USA, (402) 536-4171 EL4966E007 / 8-02 English CONTROLS (see 1) 1 ALARM RESET / SLEEP - stops active alarm for 24 hours - activates the radio for sleep function, and to select the sleep time 2 ALARM ON / OFF : switches alarm ON and OFF 3 RADIO ON / OFF - switches radio ON and OFF 4 Pigtail aerial - antenna for FM reception 5 SET AL / TIME- sets the clock and alarm time 6 MIN + : - adjusts the minutes for clock and alarm times 7 HOUR + : adjusts the hours for clock and alarm times 8 Battery door - opens to store a 4 x R6/UM3/AA batteries (not included) 9 RESET - press if the set / display does not react to operation of any button 0 VOLUME - adjusts the sound level !TUNING - tunes to radio stations @ REPEAT ALARM·BRIGHTNESS CONTROL - switches off the alarm for a 5 minute period - changes display illumination brightness - stops SLEEP function # Display - shows clock and alarm times and status POWER SUPPLY Batteries (not included) 1 Open battery door and insert four batteries (preferably PHILIPS POWER LIFE or alkaline), type R6, UM3 or AA as indicated in the compartment. 2 Remove the batteries from the set if they are exhausted or not be used for a long time. · When the batteries are turning low, appears in the display. The radio and backlight will not function, but the display and power saving buzzer will continue to operate. · When replacing batteries, the clock time and alarm setting will be stored by the self-powered back-up for 1 minute (see 'Self-Powered Back-Up'). · Make sure the radio is switched off to save battery energy. Batteries contain chemical substances, so they should be disposed of properly. SELF-POWERED BACK-UP The self-powered back-up conveniently allows your clock and alarm settings to be stored for up to 1 minute when there is a power interruption e. g. AC power failure or when changing batteries. The complete clock radio and backlight illumination will be switched off. As soon as the power supply returns the display will indicate the correct time. · If power supply returns after 1 minute, the demo mode appears and you will need to re-enter the clock and alarm setting. The model and serial number are located inside the battery compartment. BATTERY LOW MODE If you have inserted batteries, the battery low indicator · battery power is low. lights up when: SETTING THE CLOCK AND ALARM TIMES The time is displayed using the 12-hour clock with PM indicator (PM off = AM). Press SET AL / TIME twice within a second to enter the clock time setting mode. TM The clock time display flashes and you will hear a short beep. Hold down or press HOUR + or MIN + repeatedly to set and adjust the hours and minutes respectively. Release HOUR + or MIN + when you have reached the correct setting. After both the hours and minutes are set, press SET AL / TIME to confirm the setting. Press SET AL / TIME once to enter the alarm time setting mode. TM lights up and the alarm time display flashes. Hold down or press HOUR + or MIN + repeatedly to set and adjust the hours and minutes respectively. [. . . ] WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty. Do not open the set as there is a risk of electric shock!No sound ­ Volume not adjusted · Adjust the VOLUME No display backlight / display malfunction/ radio and alarm do not function ­ Set is in Power Low mode · Insert fresh batteries Display error / no reaction to any controls ­ Electrostatic discharge · Press the RESET hole inside battery compartment of the set with a ballpoint pen. Intermittent crackling sound during FM reception ­ Weak signal · Extend and position the pigtail aerial The alarm does not function ­ Alarm time/ mode not set · See SETTING THE ALARM TIME ­ Volume too low for radio · Increase the volume ­ RADIO not tuned to a radio station · Tune to a station Rattling sound. [. . . ]