User manual PHILIPS AJ3400

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the clock radio. Only use attachments/accessories specified by the manufacturer. Unplug this clock radio during lightning storms or when unused for long periods of time. [. . . ] ) b EN 4 Connect power Caution •• Risk of product damage!Make sure that the power voltage corresponds to the voltage printed on the back or underside of the clock radio. When you unplug the power adapter, always pull the plug from the socket. Never pull the cord. Set time Note •• You can only set time in standby mode. (Fig. ) d 1 PRESET/ SET TIME Note •• The type plate is located at the bottom of the clock radio. 2 2 sec HOUR (Fig. ) c 3 MIN 4 PRESET/ SET TIME 5 EN 4 Listen to FM radio Note •• Keep the clock radio away from other electronic •• For better reception, fully extend and adjust the position of the FM antenna. devices to avoid radio interference. Store FM radio stations manually You can store up to 10 FM radio stations. 1 2 3 4 5 Tune to an FM radio station. »» The preset number begins to blink. repeatedly to select a Press PRESET again to confirm. Repeat steps 1 to 4 to store other stations. Tip Tune to FM radio stations (Fig. ) •• To remove a pre-stored station, store another station in its place. e 1 RADIO ON/OFF 2 TUNING Select a preset radio station 2 sec MIN In tuner mode, press PRESET repeatedly to select a preset number. Adjust volume 3 TUNING 4 HOUR 2 sec - VOLUME + While listening, press - VOLUME + to adjust volume. »» The volume level (1~15) shows in the display. EN 6 5 Other features Set alarm timer Set alarm Note •• You can only set the alarm in standby mode. •• When alarm sounds, volume rises gradually. You cannot adjust the alarm volume manually. •• Make sure that you have set the clock correctly. Tip •• The clock radio exits alarm setting mode when being idle for 10 seconds. Select alarm source You can select FM radio or buzzer as the alarm source. ) »» The corresponding alarm icon lights up. • The AL2 setting is the same as AL1. g AL1 FM Follow the illustration to set the first alarm. • AL2: set the second alarm. AL1 f 1 AL1 AL1 2 2 sec HOUR Activate/deactivate alarm timer Press AL1 or AL2 repeatedly to activate or deactivate the alarm timer. »» If the alarm timer is deactivated, the alarm indicator turns off. AL1 3 MIN 4 »» The alarm repeats ringing for the next day. 7 EN Snooze alarm When alarm sounds, press SNOOZE. »» The alarm snoozes and repeats ringing nine minutes later. 6 Product information Note •• Product information is subject to change without prior notice. Set sleep timer This clock radio can switch to standby mode automatically after a preset period. ) h SLEEP Specifications Amplifier Total Output Power 0. 4W RMS Tuner (FM) 120 90 60 OFF To deactivate the sleep timer: • Press SLEEP repeatedly until [OFF] (off) appears. 30 15 Tuning range Tuning grid Sensitivity - Mono, 26 dB S/N Ratio - Stereo, 46 dB S/N Ratio Total Harmonic Distortion Signal to Noise Ratio 87. 5-108 MHz 50 KHz <22 dBf <49. 5 dBf <2% >50 dBA Adjust brightness Press BRIGHTNESS repeatly to adjust display brightness. General information AC power (power adapter) Brand name: Philips; Model: AS030-050EI050; Input: 100-240 V~, 50/60 Hz; 0. 15 A; Output: 5. 0 V 0. 5 A 1. 2 W <1 W i BRIGHTNESS Operation Power Consumption Standby Power Consumption EN 8 Dimensions: Main Unit (W x H x D) Weight: -Main Unit 7 Troubleshooting 191 x 104 x 69 mm 0. 33 kg Warning •• Never remove the casing of this apparatus. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. [. . . ] Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet. ) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Please inform yourself about the local separate collection system for electrical and electronic products. [. . . ]