User manual PHILIPS AJ7030DG

[. . . ] Warning Never remove the casing of this apparatus. Never lubricate any part of this apparatus. Never place this apparatus on other electrical equipment. . HHS WKLV DSSDUDWXV DZD\ IURP GLUHFW VXQOLJKW QDNHG ÁDPHV RU heat. [. . . ] The pre-installed lithium CR2032 battery can only back up time and alarm. When power is disconnected, the display backlight is off. )RU ÀUVWWLPH XVH Remove the protective tab to activate the battery. To replace the battery. Connect power c Caution Risk of product damage!Ensure that the power voltage corresponds to the voltage printed on the back or underside of the clock radio. When you unplug the AC adapter, always pull the plug from the socket. Never pull the cord. Set clock 1 2 3 4 In standby mode, press and hold SET for two seconds to activate clock setting mode. Press TUNING +/- or / repeatedly to select 12/24 hour format. Press SET DJDLQ WR FRQÀUP » The hour digits begin to blink. Repeat Steps 2 to 3 to set the hour and minute. Note If clock is not manually set, when iPod/iPhone is connected, the clock radio synchronizes time from the iPod/iPhone automatically. Turn on Press . » The clock radio switches to the last selected source. Switch to standby mode Press to switch the clock radio to standby mode. The alarm repeats ringing for the next day. Snooze alarm When alarm sounds, press SNOOZE. » The alarm snoozes and repeats ringing nine minutes later. Set sleep timer This clock radio can switch to standby mode automatically after a preset period. Press SLEEP repeatedly to select the sleep timer period (in minutes). » When the sleep timer is activated, To deactivate the sleep timer, press SLEEP repeatedly until [OFF] (off) appears. 15 30 off 60 90 120 Play audio from an external device You can listen to audio from an external device through this clock radio. 1 Connect the audio cable to: the AUX IN socket. the AUDIO OUT sockets of an external device. 2 Press SOURCE repeatedly to select AUX source. » 3 Start to play the external device (see the user manual of this device). Adjust display brightness Press BRIGHTNESS repeatedly to select different brightness levels. 7 Product information Note Product information is subject to change without prior notice. 6SHFLÀFDWLRQV $PSOLÀHU Rated Output Power 2 X 3 W RMS Tuner Tuning Range Sensitivity - Mono, 26dB S/N Ratio Search Selectivity Total Harmonic Distortion Signal to Noise Ratio FM: 87. 5 - 108 MHz FM: <22 dBf FM: <28 dBf FM: <2% FM: >55 dB General information AC Power Operation Power Consumption Standby Power Consumption Dimensions - Main Unit (W x H x D) Weight - With Packing - Main Unit Model: ASSA1E-050200; Output: 5 V; 2 A 8W <1 W 198 x 71 x 111 mm 0. 9 kg 0. 5 kg 8 Troubleshooting Warning Never remove the casing of this apparatus. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (www. philips. com/welcome). [. . . ] Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet. ) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. "Made for iPod" and "Made for iPhone" mean that an electronic DFFHVVRU\ KDV EHHQ GHVLJQHG WR FRQQHFW VSHFLÀFDOO\ WR L3RG RU L3KRQH UHVSHFWLYHO\ DQG KDV EHHQ FHUWLÀHG E\ WKH GHYHORSHU WR meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. [. . . ]