User manual PHILIPS AW7290

[. . . ] i Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. j Only use attachments/accessories specified by the manufacturer. k Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. l Unplug this apparatus during lightning storms or when unused for long periods of time. [. . . ] m DBB · Turn on or off dynamic bass enhancement. p SCAN · Scan FM/DAB radio stations. 10 EN 3 Get started Caution · Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Note · If you are not going to use the remote control for a long time, remove the batteries. English · Do not use old and new or different types of batteries in combination. · Batteries contain chemical substances, so they should be disposed of properly. Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the rear of the apparatus. ___________________________ Connect speakers Prepare the remote control Caution · Risk of explosion!Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. Note · Insert the stripped portion of each speaker wire into the socket completely. · For optimal sound, use the supplied speakers only. To insert the remote control battery: · Connect only speakers with impedance that is the same or higher than the supplied speakers. Refer to the Specifications section of this manual. 1 2 3 Open the battery compartment. Insert 2 AAA batteries with correct polarity (+/-) as indicated. Close the battery compartment. To insert each speaker wire: Hold down the socket flap. Release the socket flap. 1 3 2 1 2 For the right speaker, find the sockets on the main unit marked `RIGHT'. The position of the rectangle indicates the degree of signal strength. (The further towards the right, the greater the signal strength. ) · If there is no DAB coverage currently available, or DAB signal is too weak in your area, no DAB station will be found, and message [No DAB Station] displays, then displays [Station List]. Tune to DAB radio station manually 1 2 · Under DAB mode, press / repeatedly until your desired station name displays. » The radio immediately tune to the selected station. About station display symbols You may see some symbols displayed before the station names as follows: · : Indicates that the station is one of ten most-listened stations by you based on DAB radio's monitoring. EN 15 · · · ?: Indicates that the station is not currently available, or not active. : Indicates that the station is a primary station with secondary service. : Indicates that the station is a secondary station. Display DAB information On the display of DAB broadcasting, the first line shows station name, and the second line shows the service information for the current station. 7 types of service information are available. 1 Scan for new DAB stations New stations and services will be regularly added in the DAB broadcast. To make new DAB stations and service available on your DAB radio, a search is needed. Press INFO/RDS repeatedly to cycle through the display information (if available). » Dynamic label segment (DLS) » Program type (PTY) » Ensemble Name » Time » Channel and frequency » Bit rate and audio status » Signal error rate 1 Under DAB mode, press SCAN. » The unit starts to scan for DAB stations. Program DAB radio stations manually You can program a maximum of 30 preset DAB radio stations. Use DAB menu 1 2 3 4 1 Tune to a DAB station. Press PROG on the remote control to activate programming. [. . . ] » When sleep timer is activated, displays. 8 Product information Note · Product information is subject to change without prior notice. To deactivate sleep timer 1 Press TIMER/SLEEP repeatedly until [00] displays. » disappears on the display. Play from an external device You can also listen to an external audio device through this unit. Specifications Amplifier Total output power Frequency response Signal to noise ratio Impedance loudspeakers 2 x 2 W RMS 125 Hz - 16 kHz 60 dBA (IEC) 8 1 2 Press AUX on the remote control to select AUX source. Use an audio cable (not supplied) to connect AW7290's AUX jack (3. 5 mm, located on the back panel) to AUDIO OUT or headphone jack on the external device (such as CD player or VCR). Start to play the device (see the device user manual). Disc Laser type Disc diameter Support disc Audio DAC Frequency range Signal to noise ratio Semiconductor 12 cm /8 cm CD-R, CD-RW 24 Bits / 44. 1 kHz 125 Hz -16 kHz 65 dBA 3 Listen through headphone 1 Plug a headphone into the HEADPHONE socket (3. 5 mm, located on the back panel). Tuner FM: 87. 5 - 108MHz DAB: 174. 92 - 239. 20 MHz FM 26dB Sensitivity 20 V Total Harmonic < 5% Distortion Tuning Range Speakers Bass reflex system Dimensions (w x h x d) 20 EN 134 x 230 x 152 mm General information AC power Operation Power Consumption Standby Power Consumption Eco Power Standby Power Consumption Dimensions - Main Unit (W x H x D) Weight - Main unit with speakers 220 - 230V~, 50Hz 15 W <2W <1W Clean the disc lens · After prolonged use, dirt or dust may accumulate at the disc lens. [. . . ]