User manual PHILIPS AZ100017

[. . . ] The machine does not contain any user-serviceable parts. - Modification of the product could result in hazardous radiation of EMC or other unsafe operation. - Use of controls or adjustments or performance of precedures other than herein may result in unsafe operation. This set complies with the radio interference requirements of the European Union. 9 ­ stops CD playback; ­ erases a CD program Power Supply 5 PROG ­ programs tracks and reviews the program 0 @ VOLUME TUNING Whenever convenient, use the power supply cord if you want to conserve battery life. [. . . ] Recording and playback of material may require consent. See Copyright Act 1956 and The Performer's Protection Acts 1958 to 1972. Back panel (See 1 and 2) 6 5 Open the battery door and insert 6 batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "­" symbols inside the compartment. T 9 Source selector: CD, FM, MW, OFF ­ selects CD or radio source of sound ­ power off switch O PE 2 Replace the battery door, making sure the batteries are firmly and correctly in place. The set is now ready to operate. N 2 3 SH U FF L LI FT E O PR G 0 Telescopic antenna - improves FM reception. RE PE AT 4 !AC MAINS~ - inlet for power cord. · @ DBB ­ turns the bass enhancement on/off. # LINE-IN ­ inlet for external audio source. · Bottom panel Battery door ­ Press on the arrow and push to to insert 6 x 1. 5V R-14/ UM-2/ Ccells · · Batteries contain chemical substances, so they should be disposed of properly. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: Do not mix battery types: e. g. Only use batteries of the same type for the set. When inserting new batteries, do not try to mix old batteries with the new ones. Remove the batteries if the set is not to be used for a long time. O Meet Philips at the Internet http://www. philips. com 2 Power Supply 3 7 General Operation / Tuner Using AC power WARNING: Always check you have completely switched off the set, before you change or disconnect power supply. General operation 1 DBB BAND ON FM OFF MW Check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 1 Switching on and off and selecting the function To select your sound source, adjust the Source selector to: CD, FM or MW. 2 To switch off the set, adjust the Source selector to OFF position. @ 4 8 2 W AZ102C AZ102N AZ102S Connect the power cord to the AC MAINS~ inlet and the wall socket. The set is now connected and ready for use. Adjusting volume and sound !$ 5 PR OG 3 To switch the set off completely, withdraw the power cord from the wall socket. Adjust the sound with the VOLUME and DBB controls. 4 Install the unit near the AC outlet and where the AC power plug can be easily reached. · Disconnect the power cord from the wall socket to protect your set during heavy thunderstorms. Children could seriously injure themselves as the free end of the cable may still be live if only the connector is removed from the MAINS socket at the back of the unit. 6 x R14 · UM-2 · C-CELLS Radio reception 1 Adjust the Source selector to FM or MW. 2 Turn TUNING to tune to a station. Helpful hints: CLASS 1 LASER PRODUCT The type plate is located on the bottom of the set. To improve radio reception · Helpful hints: For FM, extend, incline and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. 6 MW FM OFF CD X ­ To avoid unnecessary energy consumption, always adjust the Source selector to OFF after using the set. LINE-IN · For MW, the set uses a built-in antenna. The display shows REP icon or REP ALL icon. Press 2; to start playback if in the stop/pause position. To return to normal playback, press REPEAT repeatedly until the modes are no longer displayed. ­ You can also press 9 to cancel your play mode. 2 3 SHUFFLE You can play all the tracks in random order. Maintenance & Safety (See 8) 7 CD player and CD handling Safety information · If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. · Place the set on a flat, hard and stable surface so that the system does not tilt. · · IMPORTANT! · The lens of the CD player should never be touched! 4 8 Finding a passage within a track · Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnet device shall remain readily operable. · Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. · The apparatus shall not be exposed to dripping or splashing. · Always close the CD door to avoid dust on the lens. · ­ · 5 3 4 PR OG Press 2; to start playback. To stop CD playback, press 9. To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. Adequate ventilation with a minimum gap of 15cm (6 inches) between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up. · · Never write on a CD or attach any stickers to it. Do not cover the ventilation openings with items such as newspapers, table-cloths, curtains, etc. · 5 6 Helpful hints: CD play will also stop when: No objects filled with liquids, such as vases, shall be placed on the apparatus. ­ · When playback of your program comes to the stop position, your set will return to normal playback. To re-enter program mode, press PROG in the stop position. 1 In the stop position, press SHUFFLE to switch on shuffle play. 2 No naked flame sources, such as lighted candles, should be placed on the apparatus. · 6 ­ you open the CD door; X The mechanical parts of the set contain selflubricating bearings and must not be oiled or lubricated. ­ you select FM, MW or OFF sound source; ­ the CD has reached the end. Reviewing the program In the stop position, press PROG repeatedly to see your stored tracks. Erasing a program You can erase the contents of the memory by: ­ in the stop position, press PROG to enter program mode, and then press 9. ­ selecting FM, MW or OFF; ­ opening the CD door; ALL Helpful hints: ­ During the shuffle play, when REP function is selected, it will play the current shuffled track repeatedly, or when the REP ALL function is selected, it will repeat the shuffle play of the entire CD. · To clean the set, use a dry cloth. [. . . ] ­ selecting FM, MW or OFF; ­ opening the CD door; ALL Helpful hints: ­ During the shuffle play, when REP function is selected, it will play the current shuffled track repeatedly, or when the REP ALL function is selected, it will repeat the shuffle play of the entire CD. · To clean the set, use a dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Environmental information All unnecessary packaging material has been omitted. The packaging can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company. [. . . ]