User manual PHILIPS AZ1002

[. . . ] This will avoid unnecessary power consumption. Adjusting volume and sound Adjust the volume using the VOLUME control. Increase and decrease the bass level by pressing DBB. The bass level can also be emphasised if you place the set against wall or shelf. Do not cover any vents; leave sufficient room around the unit for ventilation. DYNAMI C BASS BOOST 10 50 CD RAD IO CAS SET TE AZ VO LU ME Radio ­ tuning to radio stations 1 Set the POWER slider to FM or MW to select the desired wave band. 108 170 FM AM 2 Tune to the desired radio station by using the TUNING wheel. [. . . ] Display indication: the total number of tracks. TM Display indication: the current track number. PLAY ¥ PAUSE CD R ADI O CL AS AZ10 SETT E RE CO 50 RDIN G STOP PAUSE OPEN¥S TOP SEARCH PLAY RECORD 5 Press the 9 button to stop CD play. TM Display indication: the total number of tracks. You can interrupt CD play by pressing 2;. Continue CD play by pressing the button again. TM Display indication: the current track number (flashing). PROGRAM SHUFFLE CD MO DE ¥ ¥¥ S EA RC H SEARCH · · · Note: CD play will also stop if: ­ you open the CD compartment, ­ the end of the CD is reached, or ­ you move the POWER slider. If you make a mistake when operating the CD player, or if the CD player cannot read the CD, the display shows E or no. (See "TROUBLESHOOTING". ) If you press 2; and there is no CD inserted, the display shows no. 7 English Playing a CD SE CLO CD PLAYER Search backward and forward § Selecting another track Briefly press the or § button once/several times to skip to the beginning of the current, previous or subsequent track(s). During CD play: CD play continues automatically with the selected track. When CD play is stopped: Press 2; to start CD play. TM Display indication: the selected track number. Searching for a passage during CD play 1 Hold down the or § button to find a particular passage in a forward or backward direction. The recording level is set automatically. The controls VOLUME and DBB do not affect the recording. At the very beginning and end of the tape, no recording will take place in the 7 seconds during which the leader tape passes the recorder heads. Protecting tapes from accidental erasure Keep the cassette side to be protected in front of you and snap off the left tab. Now, recording on this side is no longer possible. To record again on this side of the cassette, cover the opening with a piece of adhesive tape. 10 CASSETTE RECORDER 1 Set the POWER slider to CD. 2 Insert a CD and, if desired, program the track numbers. 3 Press OPEN·STOP / 9 to open the cassette compartment. PAUSE CD RADIO AZ1050 CASSETTE RECORDER OPEN ·STOP SEARCH 4 Insert a blank, unprotected, cassette and close the cassette compartment. TM Playing of the CD or program starts automatically. 6 For brief interruptions press PAUSE ;. Press the PAUSE ; key again to resume recording. 7 To stop recording, press OPEN·STOP / 9. PLAY RECORD Note: the recording can be started from different positions: ­ if the CD player is in pause mode, recording will start from this very position (use or §); ­ if the CD player is in stop mode, recording will start from the beginning of the CD or program. Recording from the radio 1 Tune to the desired radio station (see "RADIO"). [. . . ] 6 To stop recording, press OPEN·STOP / 9. 11 English Recording from the CD player ­ CD synchro start GENERAL INFORMATION General maintenance Do not expose the set, batteries, CDs, or tapes to humidity, rain, sand, or excessive heat (caused by heating equipment or direct sunlight). - BAS You can clean the set with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. Tape deck maintenance To ensure proper recording and playback quality, clean parts A, B and C after approximately 50 hours of operation. Use a cotton swab slightly moistened with alcohol or head-cleaner fluid. Press PLAY 1 and clean the rubber pressure roller A. [. . . ]