User manual PHILIPS AZ1003

[. . . ] This warranty does not cover: a) Mileage or traveling time, pickup or delivery, cost of insurance. b) Service costs arising from failure to correctly adjust the controls of the product or to observe the instructions, or inspections that reveal that the product is in normal working order. c) Product failures caused by misuse, neglect, normal wear and tear, accidental breakage, transit damage, inexpert repairs or modification by unauthorised persons, lightning strikes, vermin infestation or liquid spillage. f) Replacement of worn or used batteries, styli or other consumables. [. . . ] 3 · 1 2 2 3 Tuner/CD Player Adjust the sound with the VOLUME control. To switch off the set, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released. · · Tuner reception Adjust the source selector to TUNER. Adjust BAND to select your desired waveband. For FM band signals, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. For MW (AM) band signals, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. To switch off the radio, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released. CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. 2 · Power Supply Whenever convenient, use the mains supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. Batteries (not included) 1 Open the battery compartment and insert six batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "­" symbols inside the compartment. (See 1) Replace the compartment door, making sure the batteries are firmly and correctly in place. Batteries contain chemical substances, so they should be disposed of properly. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: 1 3 · 4 CD Player Display indication for CD functions: ­ OP: (See 2) CD door open ­ --: (See 3) reading disc contents / no disc/ error in CD operation or CD/ CDR is blank or not finalized (see Troubleshooting) ­ During CD playback: 2 and current track number ­ 2;: (See 4) playback on pause ­ prog: when CD program is active ­ Fu: program memory full Back panel # Telescopic antenna - improves FM reception. Note: AM band antenna is built into set (see Tuner reception) General operation To select your sound source adjust the source selector to : CD, TUNER or TAPE/POWER OFF. Playing a CD This CD player plays Audio Discs including CD-Recordables. CD Player · CD-RWs, MP3 CD-ROMs, CD-I, CDV, VCD, DVD or computer CDs are not possible for playback on this set. Insert a CD/ CD-R with the printed side facing up and press the CD door gently close. Press PLAY/PAUSE 2; on the set to start playback. Press PLAY/PAUSE 2; again to resume play. To switch off the set, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released. Note : CD play will also stop when: - you open the CD compartment; - you select TUNER or TAPE/POWER OFF sound source; - the CD has reached the end of playback. 1 · 2 · CD Player Finding a passage within a track During playback, press and hold down / §. The CD is played at high speed and low volume. When you recognize the passage you want release / §. [. . . ] Do not use cleaning agents as they may damage the disc. Never write on a CD or attach any stickers to it. Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Do not open the set as there is a risk of electric shock. Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee. [. . . ]