User manual PHILIPS AZ1033

[. . . ] Recording and playback of material may require consent. See Copyright Act 1956 and The Performer's Protection Acts 1958 to 1972. Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. Refit the fuse cover. Environmental information All unnecessary packaging material has been omitted. The packaging can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company. [. . . ] Display shows --- and later, the total number of tracks. Audio CD: current track number appears MP3: The display shows current track number in the album (See 3) 4 To pause playback, press PLAY/PAUSE 2/; (See 4). Press PLAY/PAUSE 2/; again to resume play. . Helpful hints: CD play will also stop when: ­ the CD door is opened ­ the CD has reached the end ­ you select tuner or tape source. Selecting a different track 2 Switching on and off and selecting functions To switch on, push the Source selector slider to CD, TUNER, or TAPE/OFF as desired. To switch off, push the Source selector slider to TAPE/OFF and check the cassette keys are released. · Press NEXT, PREVIOUS §, once or repeatedly until the desired track number appears in the display. For MP3: first press ALBUM+ /- once or more to find your album. The display shows ALBUM and current album number briefly (See 5) · In the pause/stop position, press 2/; to start playback. Helpful hints: ­ To change from TAPE to TUNER or CD function, or when you are switching off the set: first, make sure you press the tape STOP·EJECT 9/ key to end playback and all the cassette keys are released. · Creating a MP3 CD: burn the music files from your computer hard disc on a CDR or CDRW using your CD burner. Helpful hints: Finding a passage within a track 1 During playback, press and hold § or . The CD is played at high speed. 2 Adjusting volume and sound Adjust the sound with the VOLUME and BASS BOOST controls. ­ Make sure that the file names of the MP3 files end with . mp3. ­ Total number of music files and albums: around 350 (with a typical file name length of 20 characters) ­ The length of file names affects the number of tracks for playback. With shorter file names, more files can be burned on a disc. When you recognize the passage you want, release § or to resume normal playback. Different play modes: REPEAT and RANDOM (See 6 - 8) Radio reception 1 2 3 To improve radio reception: · For FM, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. To tune to a weak FM station, adjust BAND to FM (mono). · For MW, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. Adjust BAND to select your desired waveband, MW or FM ST. (stereo) Adjust the Source selector to TUNER. REPEAT ­ plays the current track continuously REPEAT ALL ­ repeats the entire disc/ program RAND ­ tracks of the entire disc are played in random order For MP3 only: REPEAT ALBUM ­ all tracks of current album play repeatedly. 1 To select play mode, press MODE once or more. 2 Press PLAY/PAUSE 2/; to start playback. 3 To select normal playback, press MODE repeatedly until the various modes are no longer displayed. ­ You can also press 9 to cancel your play modes. CD/MP3 Player Programming track numbers You may store up to 20 tracks (for MP3: 10 tracks) in the desired sequence. If you like, store any track more than once. 2 6 Helpful hints: 3 4 5 Reviewing the program In the stop position, press PROG repeatedly until you enter the empty program location The display shows the occupied program locations After the empty program location is displayed, all the stored tracks appear in sequence. MP3 only: ALBUM and an album number appear, then a stored track number in the album is displayed. [. . . ] Cleaning of the heads can also be done by playing a cleaning cassette through once. Open the cassette holder by pressing 9/. · · · · Place the set on a flat, hard and stable surface so that the system does not tilt. Safety information Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. [. . . ]