User manual PHILIPS AZ1050-P11

[. . . ] PLAY/PAUSE 2; - starts or pauses CD playback. @ STOP 9 ­ stop playback; ­ erases a CD program. 2 1 Controls/Power Supply $ Battery door - open to insert 6 x 1. 5V R-14/ UM2/ C-cells. % AC POWER/MAINS - inlet for power cord. Power Supply · Do not mix battery types: e. g. [. . . ] To switch off the radio, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released. 2 Power Supply Whenever convenient, use the mains supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. Batteries (not included) Open the battery compartment and insert six batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "­" symbols inside the compartment. (See 1) Replace the compartment door, making sure the batteries are firmly and correctly in place. Batteries contain chemical substances, so they should be disposed of properly. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: 3 · 4 CD Player Display indication for CD functions: ­ OP: (See 2) CD door open ­ --: (See 3) reading disc contents / no disc/ error in CD operation or CD/ CDR is blank or not finalized (see Troubleshooting) ­ During CD playback: 2 and current track number ­ 2;: (See 4) playback on pause Back panel # Telescopic antenna - improves FM reception. Note: MW band antenna is built into set (see Tuner reception) CD Player · ­ prog: when CD program is active ­ Fu: program memory full · Press once briefly to return to the beginning of a current track. Press repeatedly for a previous track. CD Player 4 Repeat steps 2 to 3 to select and store all desired tracks in this way. Fu indicates the program memory is full (when you have stored tracks on all 32 program locations). To play your program, press PLAY/PAUSE 2;. To review a program · In the stop position, press PROG repeatedly to see your stored track numbers. When you recognize the passage you want release / §. Note : When searching within a final track and you reach the end of the last track, the CD goes to stop mode. 5 · 5 6 Programming track numbers You may store up to 32 tracks in the desired sequence. If you like, store any track more than once. In the stop position, press PROG to activate programming. Display shows 1 indicating the start of the program. (See 5) Press or § to select your desired track number. Press PROG to store the desired track number. Display shows your desired track number briefly followed by a number, 2 (up to 32 in sequence) indicating the next program location available. (See 6) Cassette playback 1 2 3 4 5 Adjust the source selector to TAPE/POWER OFF. Press 9/ to open the cassette holder and insert a cassette and close the deck. By pressing 5 or 6 , fast winding of the tape is possible in both directions. [. . . ] Problem ­ Possible cause · Remedy No sound /power ­ · ­ · ­ · Volume not adjusted Adjust the VOLUME Power cord not securely connected Connect the AC power cord properly Batteries dead/ incorrectly inserted Insert (fresh) batteries correctly -- indication ­ · ­ · ­ · ­ · No CD inserted Insert a CD CD badly scratched or dirty Replace/ clean CD, see Maintenance Laser lens steamed up Wait until lens has cleared CD-R is blank or not finalized/ CD-RW inserted Use a finalized CD-R or suitable CD Audio disc only Precautions & General Maintenance (See 7) · · Place the set on a hard and flat surface so that the system does not tilt. Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up. The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. [. . . ]