User manual PHILIPS AZ1205

[. . . ] China ______________________________________ LEA CUIDADOSAMENTE ESTE INSTRUCTIVO ANTES DE USAR SU APARATO. AVISO IMPORTANTE Philips Mexicana, S. A. no se hace responsable por daños o desperfectos causados por: ­ Maltrato, descuido o mal uso, presencia de insectos o roedores (cucarachas, ratones etc. ). ­ Cuando el aparato no haya sido operarado de acuerdo con el instructivo del uso, fuera de los valores nominales y tolerancias de las tensiones (voltaje), frecuencia (ciclaje) de alimentación eléctrica y las características que deben reunir las instalaciones auxiliares. ­ Por fenómenos naturales tales como: temblores, inundaciones, incendios, descargas eléctricas, rayos etc. [. . . ] For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken. This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. The best recording level is set automatically. Altering the VOLUME will not affect the recording. To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape. CD synchro start recording 1 2 3 4 Select CD source. Insert a CD and if desired, program track numbers. Playing of the CD/program starts automatically from the beginning. It is not necessary to start the CD player separately. To stop recording, press 9/. · · · Cassette playback 1 2 3 4 5 6 Adjust the source selector to TAPE/OFF. Press 9/ to open the cassette holder and insert a cassette and close the deck. Adequate ventilation with a minimum gap of 15 cm between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. . No objects filled with liquids, such as vases, shall be placed on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. 3 4 · · · · · · · · · · · · Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Do not open the set as there is a risk of electric shock. Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee. Problem ­ Possible cause · Remedy No sound /power ­ · ­ · ­ · ­ · Volume not adjusted Adjust the VOLUME Power cord not securely connected Connect the AC power cord properly Batteries dead/ incorrectly inserted Insert (fresh) batteries correctly CD contains non-audio files Press SEARCH , § once or more to skip to a CD audio track, instead of the data file. - - indication ­ · ­ · ­ · ­ · No CD inserted Insert a CD CD badly scratched or dirty Replace/ clean CD, see Maintenance Laser lens steamed up Wait until lens has cleared CD-R(W) is blank or not finalized Use a finalized CD-R(W) or suitable CD Audio disc only Display does not function properly/ No reaction to operation of any of the controls ­ Electrostatic discharge · Switch off and unplug the set. Reconnect after a few seconds The CD skips tracks ­ · ­ · CD damaged or dirty Replace or clean CD Program is active Quit program mode Note: Make sure the CD is not encoded with Copyright protection technologies, as some do not conform to the Compact Disc standard. [. . . ] ESTA POLIZA NO SE HARA EFECTIVA EN LOS SIGUIENTES CASOS: Cuando el aparato sea utilizado en condiciones distintas a las normales. Cuando el aparato no haya sido operado de acuerdo con el instructivo de uso que se le acompaña. Cuando la causa de la falla o mal funcionamiento sea consecuencia de una reparación inadecuada o alteración producida por personas no autorizadas por PHILIPS MEXICANA S. A. de C. V. PERIODOS DE GARANTIA 36 MESES. [. . . ]