User manual PHILIPS AZ1210

[. . . ] 2 Turn TUNING to tune to a radio station. To improve reception ­ For FM, pull out the telescopic antenna. Reduce its length if the signal is too strong (very close to a transmitter). ­ For AM the set is provided with a built-in antenna so the telescopic antenna is not needed. [. . . ] 4 Press PLAY·PAUSE 2; on the set to start playback. 5 To pause playback press PLAY·PAUSE 2;. To resume, press PLAY·PAUSE 2; again. 2 flashes during pause 6 To stop CD play, press STOP 9. 7 To switch off the set, adjust the source selector to TAPE/OFF position and check the cassette keys are released. Note: CD play will also stop when: ­ you open the CD compartment; ­ you select AM, FM or TAPE sound source; ­ the CD has reached to the end. CD Player Display indication for CD functions: ­ --: flashes when CD source just selected ­ In stop mode: total track number ­ During CD playback: 2 and current track number REPEAT/ REPEAT ALL: when the respective repeat mode is activated ­ PROGRAM: when CD program active ­ -- and PROGRAM: flashes when program memory full ­ Er: no disc/ error in CD operation or with the CD/ CD-(R) is blank or the disc is not finalized (see Troubleshooting) RE T PEA P M T T CD-Player Selecting a different track During playback you can use the SEARCH buttons to select a particular track. CD RAD Repeat play modes REPEAT can be selected or changed during playback in the following sequence: REPEAT ­ plays the current track continuously REPEAT ALL ­ plays the whole CD continuously CD RAD IO CASSE TT LI F T AZ1210RECORDER TTE IO CASSE TO CD SY LI F T TUNING LIFT T O O PE N CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY OPE N RDING START RECO NCHRO E STOP · OPEN VOL UM E CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT T. LOW PROGRA SEARCH DY AMI N C BASS BOO S RE T PEA TUNING LIFT T O O PE N CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT DBB CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY TO CD SY OPE N NCHRO RDING START RECO E STOP · OPEN VOL UM E T. LOW PROGRA SEARCH · If you have selected a track number in the stop or pause position, press PLAY·PAUSE 2; to start playback. · Press SEARCH § once briefly for the next track, or press repeatedly until the desired track number appears in the display. · Press SEARCH once briefly to return to the beginning of a current track. · Press SEARCH more than once briefly for a previous track. Finding a passage within a track 1 During playback, press and hold down SEARCH or §. · The CD is played at high speed and low volume. 2 When you recognize the passage you want release the SEARCH button. · At the very beginning and end of the tape, no recording will take place during the 7 seconds when the leader tape passes the recorder heads. · To protect a tape from accidental erasure, have the tape in front of you and break out the left tab. Recording on this side is no longer possible. To record over this side again, cover the tabs with a piece of adhesive tape. Synchro Start CD recording 1 Select CD source. CD RAD · Playing of the CD program starts automatically from the beginning of the program. It is not necessary to start the CD player separately. 6 For brief interruptions press PAUSE ;. To resume recording, press PAUSE ; again. To stop recording 7 To stop recording, press STOP·OPEN 9/. Press PLAY·PAUSE 2; to resume CD playback, or press STOP 9 to stop CD play. Selecting and recording a particular passage · During CD playback, press and hold down the SEARCH buttons or § on the set to find your passage. · Press PLAY·PAUSE 2; to put the CD player on pause at the selected passage. Recording will begin from this exact point in the track when you press RECORD 0. [. . . ] 6 For brief interruptions, press PAUSE ;. To resume recording, press PAUSE ; again. 7 To stop recording, press STOP·OPEN 9/ . SEARCH DY AMI N BOO S C BASS DBB 2 Insert a CD and if desired, program track numbers. 3 Press STOP·OPEN 9/ to open the cassette door. 5 Press RECORD 0 to start recording. RE T PEA 13 English P M T Maintenance Precautions & General Maintenance · Place the set on a hard and flat surface so that the system does not tilt. [. . . ]