User manual PHILIPS AZ2060

[. . . ] CD Soundmachine AZ2060 Meet Philips at the Internet User Manual Manuel d'utilisation Manual del usario Benutzerhandbuch http://www. audio. philips. com W AZ 2060 CLASS 1 LASER PRODUCT 1 2 7 1 23 4 5 6 7 3 8 X 1 4 # @ !09 8 5 9 C B A A See A $ 9 8 7 SEARCH REPEA T + VOLUME SHUFFLE - 1 2 3 4 6 A % ^ PRESET SEARCH 6 TUNIN G 5 2 English SUPPLIED ACCESSORIES -- AC mains lead TOP AND FRONT PANELS (See 1) 1 p -- 3. 5 mm stereo headphone socket Helpful hints: The speakers will be muted when headphones are connected to the set. 2 AUX -- 3. 5 mm LINE-IN jack for external audio appliance 3 STANDBYy -- power on/ off switch 4 Source selector -- selects CD/ TUNER/ AUX/ TAPE function 5 IR Sensor -- infrared sensor for remote control 6 Cassette recorder keys RECORD 0 -- starts recording PLAY 1 -- starts playback SEARCH 5/6 -- fast winds/rewinds tape STOP/OPEN 9/ -- opens the cassette compartment -- stops the tape PAUSE ; -- pauses playback or recording 7 OPEN·CLOSE - press to open/close CD door 8 DBB selector -- Switches the bass enhancement on / off 9 VOLUME -- adjusts volume level 0 Band selector-- selects wavebands !Navigation controls PRESET -, + -- selects a preset tuner station (down, up) 9 -- stops CD playback; -- erases a CD programme SEARCH , § -- CD: -- searches back and forward within a track; -- skips to the beginning of a current track/ previous/ later track Tuner: tunes to radio stations (down, up). MODE -- selects different play modes: e. g. [. . . ] ¥ For FM, extend, incline and turn the telescopic aer2 Insert a CD with the printed side facing up and ial. Reduce its length if the signal is too strong. ¥ For MW/ LW, the set uses a built-in aerial. Direct TM is displayed as the CD player scans the this aerial by turning the whole set. contents of a disc, and then the total number of tracks and playing time are shown. (See 4) Programming radio stations 3 Press 2; to start playback. You can store up to a total of 30 radio stations in the 4 To pause playback press 2;. Press 2; again to memory (20FM, 5MW and 5LW), manually or automatresume play. Helpful hints: CD play will also stop when: Manual programming ­ the CD door is opened 1 Tune to your desired station (see Tuning to radio ­ the CD has reached the end stations). ­ you select tuner, AUX or tape source. 2 Press PROGRAM to activate programming. 3 Press PRESET -, + (on the remote control 3, 4) once or more to allocate a number from 1 to 20 for FM, 1 to 5 to MW and 1 to 5 for LW. 5 Repeat steps 1-4 to store other stations. Helpful hints: You can erase a preset station by storing another frequency in its place. This 3. 5mm socket allows you to connect other audio equipment to your system e. g. 1 Press y to on, then Source Selector to select AUX. 2 Use an audio cable to connect the AUX socket to the LINE OUT/headphone socket on your external 1 To select play mode, press MODE (SHUFFLE or equipment. REPEAT on the remote control) once or more. 3 To avoid noise distortion, turn down the volume on 2 Press 2; to start playback if in the stop position. 3 To select normal playback, press MODE repeatedly 4 To adjust the sound and volume, use the sound until the various modes are no longer displayed. controls on your external equipment and the -- can also press 9 to cancel your play mode. Programming track numbers In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. [. . . ] 2 Follow steps 3-7, under CD Synchro Start recording. MAINTENANCE & SAFETY Maintenance & Safety CD player and CD handling (See 8) ¥ If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. ¥ The lens of the CD player should never be touched!¥ Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. [. . . ]