User manual PHILIPS AZ3014

[. . . ] ­ Do not connect either wires to the earth terminal in the plug, marked "E" (or the safety earth symbol) or coloured green (or green-and-yellow). Before replacing the plug cover, make certain that the cordgrip is clamped over the sheath of the lead ­ not simply over the two wires. Whenever convenient, use the power supply if you want to conserve battery life. Make sure you remove the plug from the set and wall socket before inserting batteries. [. . . ] You can erase a preset station by storing another frequency in its place. Top and front panels (See 1) 1VOLUME ­ adjusts volume level 2DBB (Dynamic Bass Boost) ­ enhances bass response 3Source selector ­ selects source of sound CD or TUNER. Also the power off switch 4Display ­ shows the CD and tuner functions 5FM· MW (AM) ­ selects FM/ MW (AM) waveband 6LIFT TO OPEN ­ opens/ closes the CD door 7PRESS TO PLAY 2; ­ starts or pauses CD play 8STOP 9 ­ stops CD playback; erases a CD programme 9SEARCH , § CD: skips or searches a passage/track backwards or forward Tuner: tunes to a station (up, down) 0PRESET +, ­ ­ selects a preset station (up, down) !PROG MODE CD: ­ programmes and reviews programmed track numbers; ­ plays tracks CD/ programme in random order; ­ repeats a track/CD/ programme Tuner: ­ programmes preset stations Back Panel (See 1) @Telescopic aerial ­ to improve FM reception #Battery door ­ to open battery compartment $AC MAINS ­ inlet for mains lead CD Player Display indication for CD functions ­ CD open: CD door open (See 6) ­ disc: CD inserted (See 7) ­ In stop mode: total track number and total playback time ­ During CD playback: elapsed playback time of current track and current track number ­ Pause: elapsed playback time freezes and flashes (See 8) ­ shuffle/ repeat modes: when the respective mode is activated ­ prog: when CD programme active); prog also appears briefly when you store a track (See 9) ­ no sel: programme activated but no tracks selected (See 0) ­ full: programme memory full (See !) ­ no prog: programme cancelled (See @) ­ no disc: no disc/ error in CD operation /CD-R(W) is blank or the disc is not finalized (See # + Troubleshooting) Playing a CD Selecting a different track During playback you can use or § to select a particular track. ⷠIf you have selected a track number in the stop or pause position, press 2; to start playback. ⷠPress § once briefly for the next track, or press repeatedly until the desired track number appears in the display. ⷠPress once briefly to return to the beginning of a current track. ⷠPress more than once briefly for a previous track. Finding a passage within a track 1 Press and hold down or §. ⷠThe CD is played at high speed and low volume. 2 When you recognize the passage you want release or §. Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. 1 In the STOP mode , press or § for your desired track. 2 When your chosen track number appears, press PROG MODE once to store the track. TM The display shows prog and prog briefly followed by your selected track number. (See 9) TM If you attempt to programme without first selecting a track number, no sel is shown. (See 0) 3 Repeat steps 1 to 2 to select and store all desired tracks in this way. TM full is displayed if you attempt to programme more than 20 tracks. [. . . ] position · To clean the CD, wipe in a straight line from the TM Display: shows no prog briefly when the centre towards the edge using a soft, lint-free programme is cancelled. Do not use cleaning agents as they may damage the disc. ⷠNever write on a CD or attach any stickers to it. Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. [. . . ]