User manual PHILIPS AZ7382

[. . . ] Recharging the ECO-PLUS NiMH batteries on board 1 Make sure you insert the rechargeable ECO-PLUS NiMH batteries AY 3362. 2 Connect the mains adapter to the 4. 5V DC socket of the player and to the wall socket. y A filled with 0­3 sections (depending on the level of charge) is shown and ChArGE is displayed. · Recharging stops when you start playback or when approximately 7 hours have passed by. [. . . ] 5 Press 9 again to switch the player off. · To remove the CD, hold it by its edge and press the hub gently while lifting the CD. ESP Note: If there is no activity, the set will automatically switch off after a while to save energy. 0 11 English Playing a CD CD PLAY Playback information · If a recordable CD (CD-R) or a rewritable CD (CD-RW) is not recorded properly, nF dISC is displayed. In that case use FINALIZE on your CD recorder to complete the recording. · If you want to play a rewritable CD (CD-RW), it takes 3­15 seconds for sound reproduction to start once you have pressed 2;. · Playback will stop if you open the CD lid. · While the CD is read, 1 -:- is flashing. English Volume and bass Volume adjustment · Adjust the volume by using VOL E. VOL. 0 Bass adjustment You can choose between the bass enhancement levels dbb1 and dbb2. 1 Press DIGITAL DBB as often as necessary to select the desired bass intensity. y dbb1 or dbb2 is displayed for 2 seconds and is shown. 2 To switch dbb1 or dbb2 off, press DIGITAL DBB repeatedly. y goes off. ITAL DIGBB D ESP 12 FEATURES Selecting a track during playback · Briefly press or § once or several times to skip to the current, previous or next track. y Playback continues with the selected track and its number is displayed. y RESUME goes off. O FF · RE SU M E ·H OL D LIN EO UT/ Locking all buttons ­ HOLD You can lock the buttons of the set. When a key is pressed, no action will be executed then. 1 Switch the slider to HOLD to activate HOLD. If the set is switched off, HoLd is displayed only by pressing 2;. a CD recorder) with a DIGITAL OPTICAL IN/AUX socket. 1 Use the mains adapter, switch ESP off and turn down the volume of the appliance that should be connected. 2 Connect an optical cable or signal lead to the OPT OUT socket of your CD player and to the DIGITAL OPTICAL IN/AUX socket of the other appliance. · To adjust volume and sound, use the controls of the connected appliance. Notes: ­ For analogue connections use the LINE OUT/p socket. ­ Playback via OPT OUT does not work if the player is supplied by batteries. 18 IN-CAR CONNECTION Only use the AY 3545 car voltage converter (4. 5 V, DC, positive pole to the centre pin) and the AY 3501 car cassette adapter. 1 Put the CD player on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the player is neither a danger nor obstacle to the driver and passengers. DIGITA L DIGITA L PROG RAM MOD E 4, 5 V DC AL DIGIT DBB ESP OF F · RE SU ME · HO LD LINE OUT / N OPE VOL. 0 2 Connect the DC plug of the voltage converter to the 4. 5V DC socket of the CD player (only for a 12 V car battery, negative grounding). [. . . ] Wrong playback direction of the car cassette player's autoreverse feature 21 English If a fault occurs, first check the points listed, before taking the set for repair. GENERAL INFORMATION CD player and CD handling · Do not touch the lens A of the CD player. · Do not expose the set, batteries or CDs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). · You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. [. . . ]