User manual PHILIPS AZ8040

[. . . ] 3 If your set is equipped with a voltage selector, located inside the battery compartment, adjust the selector to match the local mains. Disconnect the mains lead if this selector has to be reset. 2 Adjust the sound with the VOLUME and DBB (Dynamic Bass Boost) controls. 3 To switch off the set, adjust the source selector to TAPE/OFF position and check the cassette keys are released. RE T PEA T 7 Radio English 8 CD-Player Playing a CD AZ1008RECORDER TTE IO CASSE RDING START RECO LI F T Radio reception CD RAD LI F T TUNING LIFT T O O PE N TO CD SY OPE N TUNING LIFT T O O PE N CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY CD MW FM TAP F OF VOL UM E SEAR CH PAUS SEAR CH PLAY TO CD RAD RDING START RECO NCHRO OPE N AZ1008RECORDER TTE IO CASSE CD SY NCHRO E STOP · OPEN VOL UM E E BAT T. LOW CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT P STOP · OPEN T. LOW PROGRA M PROGRA RE T PEA SEARCH DY SEARCH DY AMI N C BASS BOO S AMI N C BASS BOO S DBB DBB 1 Adjust the source selector to AM or FM to select your desired waveband. [. . . ] 5 To pause playback press PLAY·PAUSE 2;. To resume, press PLAY·PAUSE 2; again. 2 flashes during pause 6 To stop CD play, press STOP 9. 7 To switch off the set, adjust the source selector to TAPE/OFF position and check the cassette keys are released. Note: CD play will also stop when: ­ you open the CD compartment; ­ you select AM, FM or TAPE sound source; ­ the CD has reached to the end. CD Player Display indication for CD functions: ­ --: flashes when CD source just selected ­ In stop mode: total track number ­ During CD playback: 2 and current track number REPEAT/ REPEAT ALL: when the respective repeat mode is activated ­ PROGRAM: when CD programme active ­ -- and PROGRAM: flashes when programme memory full ­ Er: no disc/ error in CD operation or with the CD/ CD-(R) is blank or the disc is not finalised (see Troubleshooting) RE T PEA P M T T CD-Player Selecting a different track During playback you can use the SEARCH buttons to select a particular track. CD RAD Repeat play modes REPEAT can be selected or changed during playback in the following sequence: REPEAT ­ plays the current track continuously REPEAT ALL ­ plays the entire CD continuously CD RAD IO CASSE TT LI F T AZ1008RECORDER TTE IO CASSE TO CD SY LI F T TUNING LIFT T O O PE N CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY OPE N RDING START RECO NCHRO E STOP · OPEN VOL UM E CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT T. LOW PROGRA SEARCH DY A N S BOOS MIC BAS RE T PEA TUNING LIFT T O O PE N CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT DBB CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY TO CD SY OPE N NCHRO RDING START RECO E STOP · OPEN VOL UM E T. LOW PROGRA SEARCH · If you have selected a track number in the stop or pause position, press PLAY·PAUSE 2; to start playback. · Press SEARCH § once briefly for the next track, or press repeatedly until the desired track number appears in the display. · Press SEARCH once briefly to return to the beginning of a current track. · Press SEARCH more than once briefly for a previous track. Finding a passage within a track 1 During playback, press and hold down SEARCH or §. · The CD is played at high speed and low volume. 2 When you recognize the passage you want release the SEARCH button. Note:When searching within a final track and you reach the end of the last track, the CD goes to stop mode. DY AMI N C BASS BOO S DBB 1 During playback, press REPEAT once or more until the desired REPEAT mode is shown. · To protect a tape from accidental erasure, have the tape in front of you and break out the left tab. Recording on this side is no longer possible. To record over this side again, cover the tabs with a piece of adhesive tape. Synchro Start CD recording 1 Select CD source. CD RAD · Playing of the CD programme starts automatically from the beginning of the programme. It is not necessary to start the CD player separately. 6 For brief interruptions press PAUSE ;. To resume recording, press PAUSE ; again. 7 To stop recording, press STOP·OPEN 9/. Press PLAY·PAUSE 2; to resume CD playback, or press STOP 9 to stop CD play. Selecting and recording a particular passage · During CD playback, press and hold down the SEARCH buttons or § on the set to find your passage. · Press PLAY·PAUSE 2; to put the CD player on pause at the selected passage. Recording will begin from this exact point in the track when you press RECORD 0. Note: If you press RECORD 0 during playback, recording starts automatically from the beginning of the current track. [. . . ] English If a fault occurs, first check the points listed below before taking the set for repair. Do not open the set as there is a risk of electric shock. Problem No sound No power Solution ­ Adjust the VOLUME ­ Mains lead not securely connected. Connect AC mains lead properly ­ Batteries exhausted /incorrectly inserted. Insert (fresh) batteries correctly ­ Electrostatic discharge Switch off and unplug the set. [. . . ]